How to Set Up a Stock Tank Pool: A DIY Guide
- Drill the Outlet Port. Drill a hole with a 2 3/4-inch hole saw between ridges on the pool. ...
- Add the Outlet Port. Look through your pump filter kit for the outlet port assembly and note the order of the pieces shown on the enclosed instruction diagram.
- Add an Inlet Port. Drill a hole, this time for the inlet port, somewhere down low on the pool. ...
- Attach External Parts and Hoses. Attach the various fittings on the outside of the tank designated for the inlet and outlet valves, focusing on just one valve at ...
- Fill and Test for Leaks. Remove any metal shavings found in the bottom of the pool or around the pool from the drilling done earlier.
How do I put a stock tank pool in my yard?
The first (and maybe most important) step is to flatten the area you are wanting to put the stock tank pool. If you don't level the pool out now, you'll have to drain the water to level it later.
How can I make my stock tank pool more energy efficient?
Alternate: try the lower-profile smaller, more energy-efficient 1,000 Filter Pump. Step 3: Keep your water clear and blue all summer! The last step is to maintain the water in your pool throughout the summer. Stock tank pools are great when they're clean and clear.
How long does it take to fill a stock tank pool?
After the caulk dries for at least 24 hours, you are clear to fill up the stock tank pool to the level you want! Once the water fills up past the inlet/outlet, you can then turn the pump on and water the water circulate!
Are stock tank pools any good?
Stock tank pools are great when they're clean and clear. They're not so great when murky, grimy, and full of debris, so don't forget that stock tank pools require maintenance and upkeep.
How do you install a stock pool?
Steps to install the stock tank pool filterMake sure that you have all of the parts you need. ... Find a spot for your pool. ... Make sure there is power. ... Choose the hole locations. ... Drill the holes. ... Attach the jet. ... Attach the strainer cover. ... Connect the plunger valves.More items...•
Do you need to ground a stock tank pool?
Stock Tanks Are (Usually) Above Ground Being above ground, you also do not need to dig into hard ground or blast rock to sink a pool into the ground to install a stock tank pool. All that is required is a level, solid surface. That said, it is possible to sink a stock tank pool into the ground.
What kind of pump do you need for a stock tank pool?
The pump most commonly used by DIY stock tank pool owners is the 1,500 GPH Intex filter pump, which can be found for under $200. If you have a smaller tank and want to save a little money, you can try a 1,000 GPH Intex pump, available for just over $100.
Do you need a pump for a stock tank pool?
A pool pump is a must. It will filter out debris and keep the water circulating. Without it, you'll have 700 gallons of sitting water for mosquitos and bacteria to feed on, which can be dangerous to your health.
Should I flex seal my stock tank pool?
7:4211:24We painted our stock tank pool with Leak Seal 2 years ago... How is it ...YouTubeStart of suggested clipEnd of suggested clipSo all this to say we answer the question of whether or not our leak seal inside of the pool isMoreSo all this to say we answer the question of whether or not our leak seal inside of the pool is doing great the answer is no it's not doing. Great. If you've already painted your pool with leak seal.
Is a stock tank pool a good idea?
With a stock tank pool, you can really check the chlorine twice a week and have a decently clean pool. I always skim the pool when we use the pool with a hand skimmer for leaves, bugs, and larger debris that may have fallen in. It's pretty simple to keep the water clean.
How do you keep water clean in a stock tank?
If the water in the trough is dirty and needs to be dumped, veterinarians recommend disinfecting the trough with household bleach, scrubbing the walls and rinsing it thoroughly before refilling. Up to two ounces of household chlorine bleach may be added per 50 gallons of water to discourage algae growth.
How do you keep a stock tank pool clean?
2:584:49Two SIMPLE Tips to Keep Your Stock Tank Pool CLEAN and CLEAR All ...YouTubeStart of suggested clipEnd of suggested clipI find just putting a couple of chlorine tablets in each week. Does the trick and is all that youMoreI find just putting a couple of chlorine tablets in each week. Does the trick and is all that you need to keep your stock tank cool nice and clear.
What do you need for a stock pool tank?
0:105:27Stock Tank Pool DIY! Easy Backyard Plunge Pool | How To BuildYouTubeStart of suggested clipEnd of suggested clipYou can usually find these tanks at local feed stores but due to the recent popularity of turningMoreYou can usually find these tanks at local feed stores but due to the recent popularity of turning these tanks into pools they're hard to find we were able to buy an extra one our friends stock tank
How do you level the ground for a stock pool tank?
How to Level for Your Stock Tank PoolPick your spot. Shade. ... Draw out your area. You can use a string half the diameter of your pool to draw a circle. ... Level area. Options for leveling are to dig high areas down or bring low areas up using dirt or sand. ... Check level.
Should I drain my stock tank pool for winter?
If you live in a place where it's too cold to keep your tank full, you are obviously going to need to drain it. There are a few options if this is the route you are going. First, check out how we get all the water out of our pool here. Then, you can get a pool cover or a tarp to keep water out.
How big does a stock tank need to be for a pool?
Generally speaking, stock tanks used as pools should have a length or diameter of at least 5 feet and a capacity of at least 80 gallons, equating to the size and capacity of an average bathtub.
How do I start a water pump?
To start your pump up for the first time, you will have to add water to the hoses and keep the water fully flowing to ensure air does not get sucked in. I simply dunk the hoses, fill with water and even turn on my backyard hose and insert it in the pump hoses to ensure there’s plenty of water and little to no air.
Can kids jump into a sand tank?
Some jumping and running around by small children would be fine. However, we don’t recommend teens or adults jump around or anyone jumping from a deck into the tank. Think of a disposable aluminum baking pan and how it would fare if you placed it on top of a sand base and dropped a bag of flour in it.
Do pool hoses come with end attachments?
When buying a pool pump and filter, realize that the hoses may not come with end attachments. You need at least one strainer end for the intake hose (the one that sucks up the water) so your filter does not get clogged with debris. Shhhhh, sometimes I take that strainer attachment off to vacuum out the pool.
Can you use a sand pump to keep mosquitoes out of your pool?
Absolutely, YES ! Standing water is a breeding ground for mosquitoes and bacteria. Use a cartridge or sand pump/filter (my choice) and a small chlorine tablet float. I weigh the hoses down with rocks attached with zip ties so they stay in the pool and simply attach them to the side using zip ties and clamps.
Is a pool warm in summer?
The pool will warm up during summer, but it still feels refreshing on an extra hot, humid afternoon – especially after doing yard work. In the two seasons we’ve had the tank, it has not reached a temperature that was too warm to enjoy. If your nights cool off a bit, the water temperature will also drop some.
Do you need plunger valves for pool pump?
If you were to drill holes you would need plunger valves, silicone and other tools to get the job done. (Plunger valves open and close the water flow. You don’t need those if you are not drilling holes in the stock tank.) When buying a pool pump and filter, realize that the hoses may not come with end attachments.
Where does the inlet hose go in a pool pump?
The process is easy - the inlet hose goes into the wide section of the pump (labeled with a red arrow) and the outlet hose goes into the tall canister (labeled with a blue arrow). Don't plug in or turn on the pump until you have enough water filled in the pool to cover the inlet/outlet!
Where should the inlet be on a pool?
The inlet should be toward the bottom 2/3 of the tank side wall while the outlet should be towards the top 2/3 of the tank side wall (in the 1st image you can see the inlet on the left and the outlet on the right) The cold water will then be circulated towards the top of the pool and help keep the water cool.
What to do if you don't level a pool?
If you don't level the pool out now, you'll have to drain the water to level it later. This is actually a simple step. Just lay down some paver sand, smooth it out, and use a level to check that the ground is level. If you don't have a long enough level, use a long piece of wood to stretch across the ground and set the level on top of that board.
