How many watts is a factory car amp?
Most dealers indicate the power rating of their standard factory car stereos to be 200w.
How many watts does the Acura MDX have?
The MDX with Technology and Entertainment Packages features an upgraded 529-watt 11-speaker Acura/ELS Studio Audio System.
How many watts do you need for a good car audio amp?
Answer provided by If the stereo you buy is the same as your car's original factory stereo, you should be looking at 50 to 200 watts RMS of power. If you want to make your listening experience a little easier with an aftermarket receiver, though, you might want closer to 200 to 300 watts RMS.
How many watts does my amplifier need?
Generally you should pick an amplifier that can deliver power equal to twice the speaker's program/continuous power rating. This means that a speaker with a “nominal impedance” of 8 ohms and a program rating of 350 watts will require an amplifier that can produce 700 watts into an 8 ohm load.
What sound system does Acura use?
ELS STUDIO® Premium Audio SystemCreated exclusively for Acura by eight-time Grammy® Award-winning producer and engineer Elliot Scheiner and a team of top automotive and acoustic experts, the ELS STUDIO® Premium Audio System brings the realism and artistic intimacy of the recording studio to the interior of your vehicle.
What kind of sound system does Acura MDX have?
ELS STUDIO 3D® |Introducing ELS STUDIO 3D® | Signature Edition premium audio system available on the new 2022 MDX Type S performance SUV flagship from Acura.
Is 300 watts enough for a subwoofer?
As a general rule of thumb, it is best to go with at least 300 watts in order to get enough power for your subwoofer. You can always add more speakers if you want, but it is important that the amp matches the speaker system as well.
How many amps does it take to run a car stereo?
The average regular car stereo draws from about 2 to 10 amps. If you really turn up the volume, you're typically in the 8-12 range. However, if you look to upgrade your speakers, you'll likely be closer to 30 amps!
How many watts do car speakers need?
If you're using a factory system for power, look for new speakers with low RMS wattage and sensitivity of 90dB or higher. If you're using just an aftermarket stereo for power, look for speakers with power-handling no higher than 75 watts RMS.
Is 100 watt amp too loud?
100 watts solid state = The potential to be rather loud, but there's always the volume knob. Solid states don't need to be cranked up to sound their best. In fact, many would say the louder you turn one up, the worse it sounds. 100 watts tube = Get ready for the cops to show up!
What size amp do I need for a 600 watt sub?
So you have 2 600RMS subs, so you need an amp that does 1,200RMS. So both subs will get what they need 600RMS, if you underpower subs THAT could or will damage them. Remember, its better to overpower subs then to underpower them.
What size amp do I need for 300 watt speakers?
Sample Amplifier Power Rating Chart:# of SpeakersEach Speaker Rating (RMS)Recommended Amplifier Power (RMS)1100 watts30-100 watts2100 watts60-200 watts3100 watts90-300 watts4100 watts120-400 wattsDec 20, 1999
How to use factory speaker wires?
If you're using the factory speakers, then you can use the factory speaker wires. Cut the factory speaker wire harnesses then crimp on your new speaker wire to the end of the factory wire. Route the new speaker wire to the amplifier.
How to connect a ring terminal to an amplifier?
Pull up the trunk lining and look for a ground point in the back of the trunk. Take your ground wire and crimp on a ring terminal. Wrap the connection in heat shrink then route the wire to your amplifier.
How to get power wire from battery to trunk?
To get the power wire from the battery to the trunk you'll need to go through the firewall. There is a grommet in the center of the firewall which you can route the power wire through. Figure 2. Route power wire through the firewall. After that you'll need to move it under the trim up to where the rear seats used to be.
What is an aftermarket amplifier?
But one accessory that is sure to have an impact is an aftermarket amplifier. An aftermarket amplifier gives you more control over your stereo system and can allow you to upgrade even further with higher quality speakers.
Where are the bolts on a rear seat?
These are the components you need to remove before you route the wires. For the rear seats, remove the bolt hidden in the back of the cushion then pull the two tabs at the bottom to release the seat cushion. There are two bolts at the bottom of the seat and two more hidden under the head rests.
Step 1 – Decide on Where to Mount The Amplifier
Step 2 – Remove Rear Seats, Rear Shelf and Side Trim
- These are the components you need to remove before you route the wires. For the rear seats, remove the bolt hidden in the back of the cushion then pull the two tabs at the bottom to release the seat cushion. There are two bolts at the bottom of the seat and two more hidden under the head rests. Remove the bolts then remove the rear seats. Pry up the clips on the rear shelf then …
Step 3 – Route Power Wire
- To get the power wire from the battery to the trunk you'll need to go through the firewall. There is a grommet in the center of the firewall which you can route the power wire through. After that you'll need to move it under the trim up to where the rear seats used to be. Then, route it into the trunk to your amplifier.
Step 4 – Install Fuse to Power Wire
- Solder a fuse holder to the end of the power wire facing the battery and insert a fuse. Then, crimp a ring terminal to the other end of the fuse holder. Bolt the power wire and fuse holder to the positive battery cable, but make sure that the battery cable is disconnected from the battery first.
Step 5 – Route Ground Wire
- Pull up the trunk lining and look for a ground point in the back of the trunk. Take your ground wire and crimp on a ring terminal. Wrap the connection in heat shrink then route the wire to your amplifier.
Step 6 – Route Speaker Wires
- If you're using the factory speakers, then you can use the factory speaker wires. Cut the factory speaker wire harnesses then crimp on your new speaker wire to the end of the factory wire. Route the new speaker wire to the amplifier.
Step 7 – Install Line Driver
- Take out the glove box by detaching the hooks on the sides then swinging it down and removing the two bolts in the back. This should reveal the factory amplifier. Unplug the electrical harnesses connecting to the factory amplifier. All you really need are the wires. You can leave the amplifier if you want. Cut off the ends of the wire harnesses then unbundle the wires. You'll need to look up …
Step 8 – Install Amplifier
- Now you can mount your amplifier and connect the appropriate wires from the line driver to the amplifier. Connect the speaker wires to the amplifier and the ground wire to the amplifier. Then, finally, connect the power wire to the amplifier. When you're ready to test and configure the amplifier, reconnect the battery cables.
Related Discussions