Satin Finish After you have applied all the layers of Tru-Oil to get the finish you want, let your rifle stock cure for at least a week before adding a satin finish using the Stock Sheen & Conditioner. The Stock Sheen will make the rifle stock less glossy, and it will make it a bit slippery.
Full Answer
What is the best finish for a gunstock?
Birchwood Casey True-Oil Gun Stock Finish 8-Ounce Liquid This finish is everything that you need for your gunstock. It has been around for so long, making it an old and reliable finish for your rifle. This finish contains natural oils blended with linseed oil that help provide this finish provides a luxurious, reliable, and non-yellowing finish.
How do you finish a stock with satin finish?
Using a piece of wire, hang your stock in a dust free area, where the center of the stock is at shoulder level, or a height that insures you can easily spray all areas of the stock. Spray a coat of Polyurethane Satin Finish.
What kind of oil do you use on gunstock?
Linseed oil is flaxseed oil that uses a wood finish. It is sold raw and added to oil-based paints. Boiled linseed oil is rubbed on bare wood using your hands. It gives a finish to gunstock as it gives a durable and weatherproof seal.
How do you finish a gun stock?
There are only three steps to a great finish on a gun stock. 1 Remove the old finish 2 Sand it smooth 3 Apply the new finish More ...
What is the best finish for a rifle stock?
The best finish to put on a gun stock is an oil finish. It is easy to apply, durable and can be used on finished and unfinished wood. Oil finish is also water-proof, prevents UV light from damaging the wood, and can last for several years.
What is satin gun finish?
Satin is designated for the sheen or absense of shine , in the laquer. It usually is in the laquer used 30, 60, 90 sheen used most often. higher the number ,the more lack of a shiny finish will result . Satin finishes are normally left as is when finished spraying (out of gun finish).
What do you seal a gun stock with?
0:051:03How to Seal the Wood When Finishing a Gun Stock - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is wood sealer. Apply it liberally and it will penetrate deeply into the wood. This is myMoreThis is wood sealer. Apply it liberally and it will penetrate deeply into the wood. This is my absolute. Favorite part of finishing because you can begin to see the real beauty in the wood.
Can you use Minwax on a gun stock?
0:287:46How To- MinWax Wipe on Poly Gun Stock application Part 4 - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just holding it by the stock. Get the polyurethane rubbed in and then i'm going to do a veryMoreAnd just holding it by the stock. Get the polyurethane rubbed in and then i'm going to do a very light coat i'm probably going to be putting.
What is the best coating for guns?
Cerakote is the current king of the hill when it comes to firearms finishes. A ceramic-polymer compound, it's specially formulated specifically for high-use, high-abuse-destined firearms. Several firearms manufacturers offer Cerakote as their standard finish since its wear and lubricating characteristics are excellent.
How do you dull a glossy finish?
Start by applying some mineral spirits to the wood piece or wetting the sandpaper. Next, give the surface a quick but consistent once over with 400 grit sandpaper. If you know that the finish is thicker, you may want to begin with 220 or 300 grit instead. As you sand, keep your pressure steady and your motions smooth.
Is linseed oil good for gun stocks?
Boiled linseed oil is more often used on bare wood and is popular for finishing gun stocks, as the process of heating it decreases its drying time. When hand rubbed into wood, it creates a durable weatherproof seal and the heat produced from the friction of rubbing produces a deep, polished finish.
What do you put on a wood gun stock?
0:399:20Stock Care & Storage - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe would use I will recommend using a very very small amount of Bald linseed oil which.MoreWe would use I will recommend using a very very small amount of Bald linseed oil which.
Is tung oil good for gun stocks?
We recommend using our High Lustre Polymerized Tung Oil formulation as it builds to create a well sealed and durable coating, while maintaining a hand rubbed, “gun stock” finish.
Can you wax a gun stock?
1:063:22How to Use Wax to Protect Your Firearms Presented by ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe end of each piece is cut off to see how much water has soaked in it's pretty clear that waxing aMoreThe end of each piece is cut off to see how much water has soaked in it's pretty clear that waxing a gun stock provides.
What is Tru Oil finish?
Tru-Oil® Gun Stock Finish has been the professional's choice for gun stock finishing for more than 30 years. Its unique blend of linseed and other natural oils dries fast, resists water damage and will not cloud, yellow or crack with age.
Is Minwax fast drying polyurethane waterproof?
Minwax fast-drying polyurethane is not waterproof, but it offers more resistance to water than most polyurethanes. In addition, it is a clear, oil-based finish for wood that offers more long-lasting protection than many other clear coats on finished or unfinished wood.
What does stock sheen and conditioner do?
Stock Sheen & Conditioner - The easy way to give your newly finished Tru-Oil Gun Stock a traditional satin finish or to clean, beautify and polish your old stock. Removes surface imperfections and gives your stock a smooth, hand-rubbed finish. Also protects against weather and handling.
Is tung oil good for Gunstocks?
We recommend using our High Lustre Polymerized Tung Oil formulation as it builds to create a well sealed and durable coating, while maintaining a hand rubbed, “gun stock” finish.
What is in Tru-oil?
Tru-Oil is basically linseed, plus other oils, plus mineral spirits, and I've been told that all the non-drying elements have been removed from the mixture. The secret to using it, if there is one, is to get the finish in the wood, not on the wood. This is why some people thin it, to make it penetrate better.
What is in tung oil?
What is tung oil? Originating from China and South America, tung oil—an extract from tung-tree nuts—is a natural drying oil that coats your fine wood furnishings with a transparent, wet finish. It enhances the color of your wood, offers excellent protection and is eco-friendly.
How long does it take for gunstock to dry?
You will like this finish because it takes a relatively short duration to dry, usually between 2 to 6 hours, and it will give you one of the toughest surfaces out there. You will find this formula one of the easiest to use and most straightforward to apply.
What is the finish on a knife?
The finish is USDA approved for its lack of toxins, which makes it perfect for knife handles. This finish includes a degreasing agent that removes fingerprints, oil, gun powder residue, and a lot more. Feel free to use this formula over all your wooden surfaces from your gun and knife.
Why is it important to maintain a gunstock?
Maintenance is critical if you want your gun or rifle to work correctly at all times. As the owner of a firearm, it is essential that you buy the Best Gunstock Finish as one of the ways to care for your rifle. Much as there are so many finishes for this purpose in the market, there are just a few that would give you the best result ...
What is the purpose of the buyer's guide?
The purpose of this buyer’s guide is to help you and everyone else who finds it hard to acquire the right finish for their gun stock know the critical features of the formula to consider before shopping.
Can you use steel wool for sanding whiskers?
Usually, after applying the first finish, it will “freeze,” and sanding whiskers allow for easy removal using 3/0 steel wool, which saves you the long process of steaming and de-whiskering time-consuming.
Can you use a gun stock formula on knife handles?
This formula comes with so much versatility, and you can use it on surfaces such as gun stock or even knife handles.
Can you use a tactical matte finish on a nickel gun?
You can use it on the interior and exterior of the bore without having to worry about cases of toxins .
How to dry wood stock?
Using a wet soft rag, wet the exterior of the stock with water. With this step you must take caution not to snag the wood with your rag. Let air-dry, this process will cause the fibers in the wood to stand on end, or as it’s commonly know “whiskering”.
How to remove scratches from wood stock?
Sanding with the grain, remove all rough wood and blemishes in your stock. Repeat this process with the 150 grit removing the 120 grit scratch pattern. Again, repeat this process with the 180 grit removing the 150 grit scratch pattern.
How to remove woodfill from stock?
With a piece of burlap or a coarse rag, remove the woodfill from the stock in a cross grain motion. Insure there is no woodfill left on the surface, or in the inletting. Allow 24 hours to dry. Using a soft brush, clear all the dust from the inletting area. Using the tack cloth, wipe debris from the stock.
How to hang a stock in a dust free area?
Using a piece of wire, hang your stock in a dust free area, where the center of the stock is at shoulder level, or a height that insures you can easily spray all areas of the stock. Spray a coat of Polyurethane Satin Finish. (First read directions on can.) Allow stock to dry for 30 minutes. Repeat step 11.
How to hang a stock with buttplate?
If your stock has a buttplate, leave attached and you can finish the plate along with the rest of the stock. Using a piece of wire, hang your stock in a dust free area, where the center of the stock is even with your shoulders, or a height that insures you can easily spray all areas of the stock.
How to get rid of dark wood stain?
(Note when you are finished with the rags, soak in water, and dispose of in outside container.) In a circular motion, apply a coat of Woodfill.
How long does it take for stock to dry?
Allow stock to dry for 12 hours.
What finishes can be used on gunstock?
Finishes on gunstocks vary— and there are many! Home-finishes, varnish, polyurethane, even shellac, and factory epoxy are common. Removal time and technique involved varies by the chemical nature of the finish and how strongly it’s bonded to the wood. Polyurethane seems to be the most common and can be the slowest to remove, depending on the manufacturer.
How long does it take to finish a gunstock?
As a rule of thumb, I can usually complete the stock in about two to four weeks, dependent on the backlog. It’s also difficult to predict exact return time because the way each individual gunstock receives finish, along with humidity conditions, make precise time commitments difficult.
What is satin sheen?
Sheen, defined as the degree of gloss, only has to do with a visual property, not touch — glossy sheen is really shiny; satin has a glowing shine to it, is softer in appearance, and possesses a lustrous patina. The usual idea in professional gunstock refinishing is to create this patina, making it lustrous, but without the noticeable high gloss that is a more plastic-like appearance. (Browning’s factory finishes utilize this high gloss.)
What does street value mean on a firearm?
The street value may mean something or nothing to you. As well, an extremely valuable firearm may be perceived of lesser value if modifications, including gunstock refinishing, are made to it. Really, it comes down to whether you want to focus on the collectible dollar value, or re-do the stock and get a look for your own personal enjoyment.
How long does it take for oil based finish to dry?
Sometimes up to 10, even more coats are needed to achieve deep, lustrous beauty. Drying time between coats is at least one day. Drying times also vary, depending on humidity.
How does wood absorb finishes?
Individual wood fibers within the same piece of wood absorb applied finishes differently. Some fibers act like sponges and quickly absorb, while others more repel absorbency. This creates small voids in the finish, which when viewed closely gives the wood its beautiful texture we so admire.
Is refinishing a firearm a collectible?
Disclaimer: If the gun you’re considering for refinishing is a collectible, please be advised that any alteration to the originality of the firearm, including refinishing the stock, may decrease the street value of its potential “collectible” status. The street value may mean something or nothing to you. As well, an extremely valuable firearm may be perceived of lesser value if modifications, including gunstock refinishing, are made to it. Really, it comes down to whether you want to focus on the collectible dollar value, or re-do the stock and get a look for your own personal enjoyment.
What is the best way to remove bulk from a finish?
A sharp blade or scraper - This is the fasted way to remove the bulk of your finish. A Pocket Knife is fine or you can use a card-scraper. Sand-Paper in 80, 120, 180, 220, 320 grits - I don’t recommend power sanding, Hand-sanding with a sanding block is probably best. Tape off the checkering so you don’t risk damaging it.
Can you use a chemical stripper on checkering?
Chemical Striper - Chemical Strippers should always be your last resort. I hate using them and the more I learn about harsh chemicals the less I want to use them. But at times the it is best tool for the job. Put it into the checkering, let it sit and use a nylon bristle brush to remove the finish. It may take a while. Follow the instructions on the product you use.
Can you sand a block of wood?
A sanding block doesn’t need to be fancy. It can be a dowel, a block of scrap wood, and yes your hand is sometimes the right tool for the job.
How to get a polished finish on stock?
When your stock is clean, take it out of the water, hang it and let it dry. Heating decreases the drying time, and it is a result of the friction of rubbing. That creates a polished finish. Remove the old finish before you rub the oil. Weak points become visible when the stock is clean and dry. These include cracks that have to be filled before applying the oil.
How to buff a gunstock?
Buffing your stock gun is a process that involves the application of wax to your gun stock to bring back the shining surface. Use a clean cloth to start buffing the gunstock. A thin coat will do the trick. Just the same way you buff your nails for a shiny effect is what happens on your gunstock.
What is gunstock refinishing?
Gunstock refinishing is a process that involves reviving the old finish on your gun. Amongst the multiple finishes that you can get, the focus is on linseed oil. Applying the oil is a process that involves stages.
What is a piece of sandpaper?
A piece of sandpaper is for removing the finish. Be gentle as you sand your surface. Work on the grooves and across the ridges using the block. Insert a piece of sandpaper inside the sanding block as you prepare to sand the block. Use the grain to guide you.
How to clean sawdust off gunstock?
Use the steel wool to wipe off sawdust. It gives a smooth finish to the gunstock. A cloth finalizes the cleaning process. The steel wool tears off extra grit on the outside of the stock.
What to use to remove scratches from stock?
If the stock does not have many scratches, gently sand, but if there are more scratches, use more grit. You need protective clothing before you start removing the old finish. That includes goggles, rubber gloves, and a face mask.
How to clean a gun before oiling?
Use the cloth to wipe off the old finish, dust, and dirt before you start rubbing in the oil. It has to be soft so that you do not scratch the gun.
How to remove remnants of modern finish?
Start by using a chemical stripper to remove all remnants of the modern finish. The chemical strip combined with a light sanding with 250-grit paper will put you at the start of the refinishing process.
What is the process of finishing wood with oil?
A typical oil finish of that time involved sanding the wood smooth, perhaps followed by a dewhiskering and burnishing process. Several coats of linseed oil (usually thinned with turpentine), often with a stain or color agent added, were applied to be absorbed into the wood.
Do you put varnished oil on after the first coat?
Higher gloss stocks went through the same process, but a drying product was added to the oil and more coats were applied, with the finish being allowed to "build up." If a varnished finish was desired, it was applied after the first coloring coats of oil.
Do rifle stocks have original finish?
Rifle stocks from that time period that were not given any special treatment and have survived to this day seldom offer much evidence of their original finish. As such, you might consider that the "look" you desire may be the result of a century of use.
Is it hard to finish an antique rifle stock?
Mimicking that antique rifle stock's finish might be harder than you think , but there's a tried-and-true method for finishing gun stocks. Mimicking that antique rifle stock's finish might be harder than you think, but there's a tried-and-true method for finishing gun stocks.
Can you fill pores in wood?
Filling the pores of the wood was not typically a goal of the firearm producers, except for the high-end, specialty made guns of the day. Duplicating those finishes can be done, but may involve some trial and error before you can achieve the look that you want.
What is the best oil to use on wood?
The best option and one that I use a lot is a sealant for the wood, which is much harder than French polish or oil with hardener, but looks like an oil finish and will develop a higher shine when it is rubbed with Boiled Linseed oil .
Why do old guns shine?
The mellow shine that you see on old, well-handled guns is produced by years of the oil and friction from the skin , not in a workshop. Look at the chequering on an old gun, how it is worn smooth and shiny by years of handling.
How long does it take to get an oil finish on a car?
Most customers do not want to wait for a proper oil finish to be applied; this takes weeks if not months of work and is not very shiny to begin with.
Do finishers rub oil into wood?
To speed up this process, finishers tend to rub a few coats of thin oil, such as Walnut into the wood then because of time and cost restraints, finish with a few coats of
Do stockers have their own formula?
A Most stockers or gunsmiths I know have their own way of finishing a stock and their own formula for the oils they use – and they guard their secrets like the crown jewels!
