Purchase a lineout converter to RCA- pretty much its 4 wires two positives and 2 negatives that come out of a little box with two RCAs... just go to best buy or your local electronics store and tell them you want to hook up a sub to your stock radio and you need a lineout converter to RCA thingy.. theyll hook u up.. should be no more than 20-30 bucks... or find it online cheaper
Full Answer
How to connect a subwoofer to a car stereo?
Get the remote wire in your wiring kit. Once you splice it, solder this wire to the remote wire of your stock stereo. After this is done, run the remote wire through the dashboard and the door jam. While the stereo is out, plug in the RCA red and white plugs into the Subwoofer Output, which can be found at backside of the deck.
Where to tap into speaker wire for subwoofer?
Generally if tapping into factory wires for a subwoofer, it's best to tap into the rear speaker leads. This mainly comes into play if an aftermarket radio is installed and a high pass filter is set on the front speakers to eliminate some of the bass from the front of the vehicle and of course this would take those lower frequencies away from ...
How do you hook up speakers to the radio?
We grounded to a seat bolt right here back by the amplifier, and then we grabbed speaker wire signal from the factory radio in the dash, connected that to a line output converter right behind the radio, and ran RCA cables and our blue remote turn on wire from behind the radio, down the driver's side of the vehicle, right back here to our amplifier.
Where can I get help selecting the AMP and subwoofer I Need?
If you have any questions or need help selecting the amp and subwoofer that's right for you, contact our advisors. They're available via phone and chat, and will be happy to help. Hey, I'm J.R.
How do you hook up a subwoofer to a stock radio?
0:036:05How to: Add Aftermarket Subwoofer and Amp to Factory Stereo. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the first thing you do is you want to run your power cable. So you'll see there's a fuse. So ifMoreSo the first thing you do is you want to run your power cable. So you'll see there's a fuse. So if you get an amp wiring kit it'll come with that.
Can I hook up a subwoofer to my stock car stereo?
So now you know – it's definitely possible to install a subwoofer and amplifier to your factory system, and still have it sounding good. If you'd like to know more about how to get a killer system set-up in your car without swapping your stereo, give us a call at 510-527-9888.
Can you connect a subwoofer to a radio?
If you are using your subwoofer with a home theater receiver, the connection is simple: Just run an audio interconnect cable like this one from the receiver's subwoofer output to the subwoofer's line input (pictured above). If the subwoofer has an input labeled LFE, use that one.
How do you hook up an amp to a stock radio?
6:258:28How to install an amplifier to factory radio - YouTubeYouTubeStart of suggested clipEnd of suggested clipPositive and negative is gonna go to the driver side positive negative my two gray solid gray andMorePositive and negative is gonna go to the driver side positive negative my two gray solid gray and gray with the black stripe the one with the black stripe is the one that's negative. So positive.
Do I need to bypass factory amp?
Bypassing the factory amp takes a little more work because you have to run the bypass harness to the factory amp, which is often located in some other part of the car. It's usually worth the extra effort because you'll get better sound from your new stereo, even if you're keeping those factory speakers.
Do you need a line output converter for subwoofer?
A: Yes, definitely. Amplifiers that offer speaker-level inputs don't require a separate line output converter to tap into existing speaker wires to get their signal. Many powered subwoofers offer this feature, too. The speaker-to-line level conversion is done inside the amplifier.
What do I need to install subwoofers in my car?
For the installation, you need:A 20 ft (6.1 m) power wire.A ground wire at least 3 ft (0.91 m) long.A 15 ft (4.6 m) RCA wire with both red and white connectors.A 15 ft (4.6 m) blue remote wire.Speaker wire, which can also be bought separately.A 50-amp in-line fuse and fuse holder.More items...
How do I connect bass speakers to my car?
0:553:41Adding a Subwoofer to your Vehicle - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn this case since the rear speakers are in the doors. The easiest place to tap into the rearMoreIn this case since the rear speakers are in the doors. The easiest place to tap into the rear speaker wires was in the - behind the head unit remove. The face and stereo with a few screws.
How do you amplify a factory speaker?
11:0415:38Wiring a 2 or 4 channel amp to your stock speaker harness ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou have the option of using a second set of rca's from the rear RCA output to the rear RCA inputMoreYou have the option of using a second set of rca's from the rear RCA output to the rear RCA input you can also just use a single set of RCA.
How do I hook up my amp and subs to my car stereo?
How to Connect A Car Subwoofer to An AmplifierLay the Power Cables. ... Find a Good Metal Ground. ... Plug RCA Plugs Into Subwoofer Output On Receiver. ... Use Speaker Wires To Connect The Subwoofers To The Amplifier. ... Connect the Power Cable to Battery.
How do you hook up a line output converter to a factory radio?
0:398:28How To Install a Line Output Converter (LOC) To Any Car (Simple)YouTubeStart of suggested clipEnd of suggested clipSo for this install you're going to need your line output converter I would recommend picking upMoreSo for this install you're going to need your line output converter I would recommend picking up electrical buck connectors. And electrical wiring cutter. So you can splice your wires.
8 Steps To Install A Subwoofer To A Factory Stereo
The steps of adding a subwoofer to a factory stereo are quite easy to keep track of. There's no need to be concerned. You should be OK if you just follow along.
How To Install A Powered Subwoofer To A Factory Stereo?
To safeguard yourself and your equipment during installation, it goes without saying that you must disconnect the negative battery terminal before beginning any electrical operation.
How To Add Subwoofer To Stock Stereo?
It is simply a small converter that connects to your speaker wires and provides RCA inputs. The main issue is that you won’t receive the authentic sound quality from your subwoofers.
Final Words
If you currently have a decent infotainment system from the factory but want to improve your car audio experience, installing a subwoofer could be the ideal solution. And to do so, you must know how to install a subwoofer to a factory stereo. Hope this post was useful in teaching you the fundamentals of the procedure.
Why add a subwoofer to a car stereo?
Adding a subwoofer to your factory stereo is a great way to improve your sound without giving up your familiar factory controls. In this video, you can follow along as one of our experts installs an amplifier and subwoofer in a car with a factory stereo. You'll see all the basics of amplifier installation, including:
Can you drive a subwoofer without an amp?
If you intend to drive that subwoofer without an amplifier and it's not a powered sub, that won't work. Your radio or even factory amp isn't going to be able to do it. And underpowering will be detrimental to the sub and whatever is underpowering it.