Usually, you'll be installing a 4-channel amplifier with speaker-level inputs. The best way to connect it to a factory system is to tap into the stereo's speaker outputs for the amp's input signal. Then send the amp's outputs back to the stereo's harness, and on to the speakers through the factory wiring.
Full Answer
How to connect a subwoofer to a car amplifier?
With the speaker wires, connect the subwoofer system wiring to the amplifier. Make sure that you connect the speaker wires to the negative and positive outputs of your car’s amplifier. Route the speaker wires to where the subwoofer is located.
How do you add bass to a factory stereo?
This has been the tried-and-true method of installing bass systems to factory stereos for decades. It’s just a simple little converter that ties into your speaker wires and provides RCA inputs.
Can I install a subwoofer and amplifier to my factory system?
So now you know – it’s definitely possible to install a subwoofer and amplifier to your factory system, and still have it sounding good. If you’d like to know more about how to get a killer system set-up in your car without swapping your stereo, give us a call at 510-527-9888.
What amplifiers can be installed into a factory audio system?
While almost every amplifier is capable of being installed into a factory audio system when paired with the right accessories, there are some that were made specifically for it! Here are the two we tend to favor the most: The Kicker Hideway is a self powered subwoofer. Meaning, it is a subwoofer in an enclosure with an amplifier already built in.
How do you hook up a sub and amp to a stock radio?
How To Install A Subwoofer To A Factory StereoStep 01 : Gather all necessary equipment.Step 02 : Choose a speaker and an amp.Step 03 : Remove the battery from the vehicle.Step 04 : Disconnect the wires of the speaker.Step 05 : Identify the relevant connections.Step 06 : Run wires.Step 07 : Reinforce the connections.More items...•
How do you hook up a subwoofer and amp on a Mustang?
0:4023:12How To Install A Subwoofer & Amp on a 2017 Mustang w/ Stock HeadunitYouTubeStart of suggested clipEnd of suggested clipYou pull it through on the interior of the car. Uh it goes underneath these interior panels you canMoreYou pull it through on the interior of the car. Uh it goes underneath these interior panels you can tuck it under or take these panels off and then put the wire underneath.
Can I install a subwoofer with a stock radio?
Adding a subwoofer to your factory stereo is a great way to improve your sound without giving up your familiar factory controls. In this video, you can follow along as one of our experts installs an amplifier and subwoofer in a car with a factory stereo.
What do I need to install a subwoofer and amp?
1:1614:22How to install an amp and sub in your car | Crutchfield video - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe had an aftermarket stereo that stereo would have RCA preamp outputs already on it that we couldMoreWe had an aftermarket stereo that stereo would have RCA preamp outputs already on it that we could use you know connect RCA cables directly from there run them to the back.
Is there an electric Ford Mustang?
The Mustang Mach-E Select has a $43,895 base price. This trim is fitted with the standard-range battery pack, one electric motor, and rear-wheel drive. It has a 247-mile driving range. Upgrading to all-wheel drive costs $2,700, and it adds a second electric motor but reduces the driving range to 224 miles.
How many speakers are in a 2020 Mustang?
A soul-stirring 12-speaker system powered by 900 watts delivers a passionate and powerful audio performance precisely engineered to match the Mustang's unique sound profile.
Can you hook up an amp to a stock radio?
Another popular way to connect an amplifier to a factory radio is to use something called a line output converter. It connects to the factory radio's speaker wires and converts the speaker-level signal to a preamp-level signal. This lets you use RCA cables to run that signal to your amplifier.
Do you need a line output converter for subwoofer?
A: Yes, definitely. Amplifiers that offer speaker-level inputs don't require a separate line output converter to tap into existing speaker wires to get their signal. Many powered subwoofers offer this feature, too. The speaker-to-line level conversion is done inside the amplifier.
Do I need a new stereo for subs?
You won't get the exact same sound quality from your subwoofers as you would if you had an aftermarket stereo (like Alpine or Kenwood) in your car. The reason is that you're not enhancing the voltage of the stereo, and therefore aren't giving it the proper “juice”.
What do you need for subs?
You'll want to gather your component sub(s), enclosure, speaker wire, amplifier, (or a powered sub), an amp wiring kit, signal cables, and any tools you think will come in handy.
How much does it cost to install an amp and subwoofer?
A: Standard installation is $149.99 (https://bby.me/zaahw) A materials charge of $5 per vehicle will be assessed at time of installation, and standard installation does not include vehicle-specific parts or accessories. For subwoofer installation, parts typically cost $20–$300, but will vary.
What do you need to hook up a subwoofer?
1:443:47How to install a powered subwoofer in your car | Crutchfield videoYouTubeStart of suggested clipEnd of suggested clipBoth the turn on wire and RCA signal cables need to be connected to your stereo. Run these cablesMoreBoth the turn on wire and RCA signal cables need to be connected to your stereo. Run these cables behind the dash to your stereo.
Step 1 – Disconnect battery
Disconnect the negative battery terminal (black), then wrap it in a towel so it doesn't touch any metal around the hood.
Step 2 – Install amp power wire
The amp power wire will need to be installed to the positive battery terminal. To do so, remove the positive battery terminal bolt, but don't remove the clamp. Put the power wire over the bolt and tighten it back to the battery using your 10mm socket.
Step 3 – Route power wire into wheel well
To route the power wire from the battery and into the wheel well, you will need the screws on the back of the passenger's side wheel well. There are four Phillips head screws that require one counterclockwise turn to remove. Remove the back half of the wheel well cover, and route the wire from the battery and into the wheel well.
Step 4 – Remove trim to access the wire
Remove the passenger's side rocker panel molding. You can do so by gently pulling it up and away from its clips. Remove the fuse plate to pull the passenger's kick panel out, and it will come off the clips. Finally, remove the rest of the kick panel by pulling it backwards, away from the front of the car, and it will come off its clips.
Step 5 – Route the wire into the cabin
Route the wire through the gromet in the firewall. You can drill it so it fits the wire, or you can cut part of it to make some room for the wire to go through. Route the wire through that hole and tape it to avoid water from entering into the cabin.
Step 6 – Remove the rear seat
Now you need to route the wire into the trunk where the amp will be located. Press the tab under the seat and lift it up to remove.
Step 7 – Route the wire to the trunk
Feed the wire through the rocker panel and under the carpet. Keep feeding it through the rear quarter panel, then grab the other end from the rear seat. The power wire should go under the back seat and into the trunk.
How to connect subwoofer to amplifier?
With the speaker wires, connect the subwoofer system wiring to the amplifier. Make sure that you connect the speaker wires to the negative and positive outputs of your car’s amplifier. Route the speaker wires to where the subwoofer is located. If the amplifier is located away from the subwoofer, make sure that you run the wires under ...
Where is the remote wire on a stereo?
Once you remove the stock stereo, you will see a blue and white wire, which is basically your remote wire. This wire is located at the back of the stereo deck. Get the remote wire in your wiring kit. Once you splice it, solder this wire to the remote wire of your stock stereo.
What color wire is used for 12V?
In your amplifier wiring kit, generally a red in color wire is the longest one, which is the 12v power wire. You need to pass the wire through the firewall. Start from the battery and pass on to the amplifier. However, do not connect the wire to the amplifier or battery yet.
Can you connect speaker wires to subwoofer?
You can now connect the speaker wires to the subwoofer. Make sure that the corresponding inputs in the subwoofer are paired correctly — negative to negative and positive to positive.
How to connect speaker wires to amplifier?
Run those wires to the amplifier and connect them into the input section of the amplifier. Now connect your second harness to the speaker wires that lead into the dash and run them to the output section of your new amplifier.
How to run a remote to an amp?
Run your remote wire from a source that has 12v only while the vehicle is running to your amplifiers remote input. run power wire from battery to amp. Run ground wire from proper chassis ground to amp. Run speaker wire from amp to subwoofer.
What are the different types of amplifiers?
But, there are a few styles of amplifiers that make it a lot easier to integrate with the factory system without the need to replace any existing things. Subwoofer Amplifiers – Amplifiers dedicated to powering subwoofers. 2 channel amplifiers – Amplifiers that power 2 speakers. 4 Channel amplifiers – Amplifiers that power up to 4 speakers.
What is Alpine Power Pack?
The Alpine Power Pack is another amplifier that has made factory integration way easier! it has a internal Hi/Lo and comes with an input and output harness that will usually allow you to install it without any additional parts even. Its considered a mini amplifier because of its small footprint and can generally be installed into hidden locations around your car.
What is a 2 channel amplifier?
2 channel amplifiers – Amplifiers that power 2 speakers. 4 Channel amplifiers – Amplifiers that power up to 4 speakers. 5 channel amplifiers – Amplifiers that power up to 5 speakers including 1 subwoofer. While almost every amplifier is capable of being installed into a factory audio system when paired with the right accessories, ...
Do all amplifiers need the same parts?
Its important you know that not all amplifiers require the same parts during installation. For example, the Alpine Power Pack 4 channel amplifier comes with the mounting parts, wiring and fuse needed to install right out of the box while standard amplifiers might need a few more things.
Do you need RCA wires for a subwoofer?
This channel usually takes the sum of your rear/front or both amplifier inputs to create a proper subwoofer output channel. You won’t need anymore RCA input wires, just a bit of subwoofer speaker wire.