Attatch your RCA wires to that RCA channel and run that to the input section of your amp Run your remote wire from a source that has 12v only while the vehicle is running to your amplifiers remote input run power wire from battery to amp
Full Answer
Is there a Dodge stereo wiring diagram?
It’s that easy! The best part? Every Dodge stereo wiring diagram contains information from other Dodge owners. If you want to install a car stereo and save time, you’ll love our Dodge stereo wire guide.
Do Ram Trucks have stereo stereos?
From the most basic of fleet-ready regular cab trucks to ultra-luxurious megatrucks that can tow pretty much anything short of a cruise ship, the Ram lineup is pretty impressive. The stock stereos, however, kind of aren't.
What size subwoofer does the 2012 Ram 1500 have?
This is the 2012 Dodge Ram 1500 with the premium sound system with the 8 inch factory sub by the way. So here is a pic of my LC2i Line Out Converter. On the top left, I have the four wires from the factory wiring going into their designated spots. I've read that some people used all four wires whereas others only used two?
Where are the speakers on a Ram pickup?
The Ram pickup has 3-1/2" speakers on either side of the dash (Crutchfield Research Photo) The corner dash speakers are 3-1/2" models. The non-Alpine speakers are wired in parallel with the front door speakers. Replacing these speakers is basically the same as replacing the center speaker.
How do you hook up a amp to a stock radio?
The best way to connect it to a factory system is to tap into the stereo's speaker outputs for the amp's input signal. Then send the amp's outputs back to the stereo's harness, and on to the speakers through the factory wiring.
Can you hook up a subwoofer and amp to a stock radio?
Adding a subwoofer to a factory stereo is an excellent method to boost your sound while retaining your factory controls. The nifty devices can produce bass and sub-bass sounds at low frequencies. Thankfully, it's pretty simple to wire one into an existing car stereo system.
How do you hook up amps and subs to a factory radio?
3:236:05How to: Add Aftermarket Subwoofer and Amp to Factory Stereo. - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou would run cable that goes from that and plug directly into here I have speaker inputs and so nowMoreYou would run cable that goes from that and plug directly into here I have speaker inputs and so now what that does is it allows you to tap off of a speaker wire.
Can you add subwoofers to a stock sound system?
So now you know – it's definitely possible to install a subwoofer and amplifier to your factory system, and still have it sounding good. If you'd like to know more about how to get a killer system set-up in your car without swapping your stereo, give us a call at 510-527-9888.
How do you hook up subs to a factory car stereo?
As shown in the diagram below, to receive an input signal from your factory car stereo you would just need to tap into your rear speaker wires. Then, you would run RCAs from your LOC to your amplifier. Finally, connect your subwoofer to the amplifier using speaker wire as you would normally.
Do I need to bypass factory amp?
By bypassing the factory amplifier, the music sounds more detailed and clear than it did when he used the amplifier integration harness. Whenever there's one available, we recommend bypassing the factory amp to get better sound. If you're considering a new stereo for your vehicle, keep this option in mind.
How do you wire a RCA cable to a stock radio?
0:126:03How to add RCA Pre out adaptor to a factory car radio guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd it's part number pc2 so one and what that is is basically it's got speaker wires on one end withMoreAnd it's part number pc2 so one and what that is is basically it's got speaker wires on one end with an earth and RCA connectors on the other end that you can plug your RCA cables into.
Do you need a line output converter for subwoofer?
A: Yes, definitely. Amplifiers that offer speaker-level inputs don't require a separate line output converter to tap into existing speaker wires to get their signal. Many powered subwoofers offer this feature, too. The speaker-to-line level conversion is done inside the amplifier.
How do I connect my amp to my head unit?
2:064:34How to install a car amplifier | Crutchfield DIY video - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe turn on wire is included in your amp wiring kit. Run these cables behind the dash to your stereoMoreThe turn on wire is included in your amp wiring kit. Run these cables behind the dash to your stereo. The turn on wire connects to a remote turn on lead in your stereos wiring harness.
Can you hook up an amp without RCA cables?
Don't worry as you can still install an amp without using RCA cables. You just have to make sure that the factory radio can accept speaker-level inputs or line-level connections. Aside from that, also check the root means square power or RMS power of the amp.
Will adding an amplifier make speakers louder?
They Drastically Improve the Sound Quality Factory speakers will tend to crackle and distort the music as you turn up the volume, but speakers that are fed via an amplifier will not. The result of adding an amplifier, regardless of how small or cheap it is, will be cleaner, louder, bassier and distortion-free music.
Why upgrade bass in a ram truck?
Upgrading the bass in your Ram truck is a great way to get even more enjoyment out of your music. How much you can add depends on what you're starting with.
What size speakers are on a standard cab truck?
Standard Cab trucks feature a pair of 6"x9" speakers in the rear side panels. Like their cousins in the doors, they can be replaced by same-size, 6-1/2", or 5-1/4" aftermarket models. You'll need mounting brackets for the smaller ones, and they're included at a discount when you buy your speakers at Crutchfield.
Why do you need a camera on a ram truck?
A rear-view camera will help increase your visibility and safety when your busy day takes you into town. And a camera is also a huge help when you're backing up to a trailer.
What size are Alpine roof speakers?
The rear roof speakers, found in Alpine-equipped trucks, are 2-1/2" tweeters. Removing them is easy and aftermarket replacements are available, but installing the new ones will take a little work on your part, because there are no mounting brackets available.
Overview of The Dodge Ram
Factory Stereo System
- The Ram's base stereo was a reasonably decent 6-speaker system. Options included satellite radio, steering wheel audio controls, Bluetooth® connectivity, a touchscreen receiver, a rear-view camera and, in the larger trucks, a rear-seat entertainment system. The top trim level, available only on Crew Cab and Quad Cab trucks, included a 10-speaker Alpine system with a subwoofer u…
Removing The Factory Radio
- Removing and replacing your truck's stock radio isn't that hard, but with many receivers, you'll need to modify the radio cavity. Use a hacksaw to cut off the “arms” of the center metal frame where the “arms” join the side metal frame on each side, then pull out that center frame. This won't affect the structural integrity of the dash or anything –...
Removing The Factory Speakers
- The number of speakers in your Ram truck depends on the cab style and the stock radio system. None of the speakers are terribly difficult to replace. In all cases, however, it's important to remember that replacing these 1- or 2-ohm factory speakers with a higher-impedance aftermarket speaker will result in lower volume levels. Shop accordingly, and if you have questions, just give …
Bass in Your Ram Truck
- In Alpine-equipped Quad Cab and Crew Cab Rams, the 8" Alpine factory subwoofer is mounted to a polymer enclosure under the right rear seat. To replace it, you'll need to remove the enclosure from the truck, then remove the sub from the enclosure. None of this is hard to do, but it's not like you just reach under the seat and pull the thing out, either! The step-by-step instructions can be f…