Refinishing a Gunstock with Tru-Oil for a High Gloss Finish
- Remove the old finish and strip your project back to bare wood. I use Sunnyside Corporation’s stripping solution. ...
- Sand the gunstock free of scratches ending in 600-grit. To be perfectly clear, use rough grit paper if you’re getting rid of scratches. ...
- Take a t-shirt, cut it up. ...
- Use the lint-free strips to dab on Tru-Oil and rub into the wood. ...
Full Answer
How do you use Tru oil gun stock finish?
Sep 23, 2015 · I show you how to finish or refinish a rifle stock with Birchwood-Casey Tru-oil Gun Stock Finish. Tru-oil is also a popular guitar finish. Using a few diff...
Why Tru-oil for gunstock refinishing?
Jan 26, 2021 · Apply Tru-Oil. Use gliding strokes. Start with the least amount of oil - a little oil goes a long way. Rub the oil over small areas and gradually expand. Rub until your finger starts to feel tacky. Blend each stained portion together for a consistent look.
What kind of oil do you put on a rifle stock?
Refinishing a Gunstock with Tru-Oil for a High Gloss Finish Step 1: Remove the old finish and strip your project back to bare wood.. I use Sunnyside Corporation’s stripping... Step 2: Sand the gunstock free of scratches ending in 600-grit. To be perfectly clear, …
How do you oil a Casey rifle stock?
Jul 20, 2020 · Put it into the checkering, let it sit and use a nylon bristle brush to remove the finish. It may take a while. Follow the instructions on the product you use. This process will take time. Go slow and don’t rush it. You can use mineral spirits or water to “wet” the surface which will help you find missed spots of old finish.
How many coats of Tru oil are on a gun stock?
What kind of oil do you put on gun stocks?
What is the best oil to finish a gun stock?
How many coats of linseed oil should you put on a gun stock?
What is in Tru-oil?
Can you use old English on gun stocks?
Is Tru oil durable?
What is Birchwood Casey Tru oil?
What oil do you use for walnut stock?
Can you use Tru-oil over linseed oil?
Linseed oil or Tung oil would not qualify. This is because Tru-oil is primarily a varnish. On the other hand, in my experience, linseed oil is much better for sinking into the wood for the first few coats. That gives a lot more liveliness of the grain in the finished object.Jan 25, 2009
Is Tru-oil linseed oil?
Is tung oil good for gun stocks?
How long to wait to apply Tru-Oil to Birchwood Casey?
After waiting at least 24 hours, use very fine steel wool to lightly remove any dust that may have settled while drying before moving on to the next step. Apply Tru-Oil. Birchwood Casey Tru-Oil is sometimes easier to apply to your rifle stock using bare fingers.
How to remove old finish from rifle?
After the stock is removed, the most effective way to remove the old finish is to sand it by hand.
How to fix scratches on a rifle?
Apply Filler. Once you have sanded off the old finish, look for any remaining scratches or gouges. If there are any, fill those in with a wood filler. After letting the filler dry, sand down the spots that have just been filled so that the rifle’s stock is even and smooth. Apply Walnut Stain.
How to get darker walnut stain?
To get the color that you want, just add water and spot test the stain on a piece of scrap wood until the right consistency is achieved. If you decide you like the darker stain, no water is necessary.
Can you use water to stain walnut?
If you decide you like the darker stain, no water is necessary. For most refinishing applications, a 50/50 water/stain mixture is just about right, but this depends on your personal preference and the original color of the stock. Apply the walnut stain with a clean, dust-free cloth and let it dry overnight.
What is a CZ Woodcock G2?
I bought a CZ Woodcock G2, a Turkish shotgun manufactured by Huglu and imported by CZ USA. At the price I paid for it new ($650 at the time of this writing), I’m happy. The action is case hardened and unique-looking, it has scroll engraving, removable chokes, and a great carrying case. The finish is fine, and frankly, I had no interest in refinishing this when I had bought it. However, after pulling some of the finish off completely with tape, work needed to be done.
Is Tru Oil a varnish?
As far as characteristics go Tru-Oil isn’t much of an oil at all. In fact, it’s a varnish with some linseed oil for color. You wipe on coats and build layers of hard film on top of the wood, which allows you to buff it back for a polished finish. The downside is that Tru-Oil is closer to spraying on a finish.
Can you use a soft knife to scrape a muddy finish?
It works okay. It breaks down the top layer of that muddy finish enough to be scraped back with a credit card. If you are bold enough, you can also use the spine of a soft knife to scrape away the old finish. Next time, I’ll use the product that most people recommend: Citristrip.
What to use to scrape muddy finish?
It breaks down the top layer of that muddy finish enough to be scraped back with a credit card. If you are bold enough, you can also use the spine of a soft knife to scrape away the old finish. Next time, I’ll use the product that most people recommend: Citristrip.
Step 1: Remove the Old Finish
Isn’t this hideous? This is all the factory varnish scraped off with my pocket knife. Hold the sharp knife 90-degrees to the surface and scrape. It’s oddly satisfying.
Step 3 - Apply Tru-Oil
This is where things can get made complicated but don’t need to be. In my video I made it a little over-complicated. I think you get the same results by applying a coat, letting it dry, lightly wet sand, and repeat two more times.
Who is Jim Carmichel?
Thanks to Jim Carmichel for his help with this guide. In addition to having been the Shooting Editor for Outdoor Life magazine, Jim is an accomplished gunsmith with tremendous insight on wood finishing, blueing, and browning metal. Follow Carmichel’s Tips and you’ll make your gun everything it deserves to be!
Is sanding wood a good finish?
Sanding is a critical step in any wood finishing venture. Yes, it can be tedious. And sometimes it is easy to tell yourself “that’s good enough” in order to get on with the more glamorous process of finish application. Resist the temptation to cut corners, because the finish will actually accentuate scratches and other imperfections in the wood.
How to keep stock edges sharp?
To keep stock edges sharp and the wood’s surface ripple-free, always sand with a sanding block. The block will prevent the abrasive from “digging in” on soft spots in the grain. And remember to sand AROUND checkering to keep the checkered peaks crisp. Keep checkering masked off until final application of oil.
Can you stain Birchwood Casey Walnut?
Birchwood Casey Walnut Stain is a water-based stain that will produce a clear, rich walnut color without grain clouding or smearing.
What is Birchwood Casey Walnut Stain?
Birchwood Casey Walnut Stain is a water-based stain that will produce a clear, rich walnut color without grain clouding or smearing. 1 As a test to determine whether to stain or not, examine a portion of the wood while it is wet with water or alcohol.
How to control the color of walnut stain?
2 Walnut Stain is a concentrate solution; color intensity is easily controlled by adding water. Dilute with water before using to achieve a lighter color; or leave full strength for a darker color. It’s best to test color intensity on a scrap piece of wood. Generally 50/50 stain and water mix works for most situations.
How to get darker wood color?
Dilute with water before using to achieve a lighter color; or leave full strength for a darker color. It’s best to test color intensity on a scrap piece of wood. Generally 50/50 stain and water mix works for most situations. 3 Apply Walnut Stain with a clean, lint-free cloth or brush.
How to apply Tru Oil?
Apply the Tru-Oil with your bare hand only a couple of drops on the end of your finger, rubbing thouroughly till it starts to dry or tack then move to another spot. After several coats then steel wool lightly don't break through the oil finish or you will create a spot that won't stain well. Good luck. Michael Markey.
Can you stain a gun stock?
If you stock is made of black wallnut it will be dark anyway. If you gun stock is made of birch it will be light colored and you will have to stain it. Many less expensive rifles and shotguns were stocked with birch wood.