Clamp Rifle In Vise: Lightly clamp the rifle in the vise in a horizontal position. Wait 10 hours for the compound to dry, then follow the kit directions to lift the barreled action from the stock. This might require a light tap on the barrel’s underside with a rubber hammer.
Full Answer
How do you remove the firing pin from a db308?
Push in the firing pin retaining pin right to left of the bolt carrier and remove it by pulling it out to the left. Tilt the bolt face up and allow the firing pin to slide out of the bolt body. (n/a for DB-9R) Push the bolt in towards the carrier until it rotates and comes to a stop, then turn the cam pin 90 degrees. FOR DB308 ONLY: DO NOT TURN
What is Diamondback Firearms' Policy on product descriptions?
Diamondback Firearms reserves the right to edit, change, or clarify descriptions at any time to correct errors in product listings. In the event of inaccuracies in the description of an item, we reserve the right to remove the conflicting information once notified.
How do I Clean my 14A db-9r 20 upper receiver?
PICTURES MAY VARY FROM YOUR PRODUCT FIG. 14a DB-9R 20 CLEANING PROCEDURE Upper Receiver – Clean the following with Rifle Bore Cleaner: All areas that show powder fouling, including the bore and chamber; the locking lugs and bolt body and the gas tube protrusion inside the upper receiver.
When should I replace parts on my Diamondback firearm?
COMMONLY REPLACED PARTS Some parts wear with extended use. You should always replace these parts when you notice wear. Below is a list of these parts with Diamondback Firearms ordering information Extractor Extractor Spring with Insert Gas Rings Firing Pin Firing Pin Retaining Pin Bolt Cam Magazine
What ammunition is used in diamondback rifles?
Diamondback Firearms recommends the use of high quality, domestically produced ammunition for best results and highest accuracy. For plinking and practice, we recommend only domestic, commercially manufactured ammunition or high quality surplus NATO specification ammunition.
Where is the selector lever on a rifle?
A selector lever, located on the left side of the lower receiver, has two positions. “FIRE” and “SAFE”. When set to “FIRE” the firearm will fire a single shot each time the trigger is squeezed. When set to “SAFE” a cam bears upon the rear of the trigger, blocking movement and preventing the hammer from being released.
What to do if a gun does not operate?
If the gun sounds different or does not operate, unload the firearm and make sure the barrel is free from obstruction before continued firing. Do not allow anyone to handle or attempt to fire a DIAMONDBACK FIREARM until they have read and understand this manual and the procedures for safe operation and safe gun-handling.
How to lock a bolt on a rifle?
To lock the bolt open, pull the charging handle rearward (Fig. 7), press the button of the bolt catch and allow the bolt to move forward until it engages in the bolt catch. Return the charging handle to forward. If you haven’t already done so, place the rifle on . “SAFE”.
What happens if you carry a firearm in a poorly ventilated area?
“Discharging firearms in poorly ventilated areas, cleaning firearms, or handling ammunition may result in exposure to lead and other substances known to cause birth defects, reproductive harm, and other serious physical injury. Have adequate ventilation at all times. Wash hands thoroughly after exposure.”
When was the DiamonDBACK Act passed?
ACT which is effective for goods manufactured on or after December 31, 1976. DIAMONDBACK FIREARMS, LLC. warrants that this firearm was originally manufactured free from defects in material and workmanship.
What causes a bullet to ricochet?
Water or other surfaces can cause ricochets. Be sure your bullet will stop behind your target. Bullets can ricochet off many surfaces, such as rocks, and travel in unpredictable directions with considerable velocity. Do not fire randomly into the sky. Make sure your “audience” maintains a five foot distance behind you.
Jerry
i have searched and can't find anything. how do i remove my collapsable stock butt stock on my DPMS LR-308 oracle. i am replacing it with a magpul one. thanks
Frankh252
i have searched and can't find anything. how do i remove my collapsable stock butt stock on my DPMS LR-308 oracle. i am replacing it with a magpul one. thanks
Robocop1051
Frank, that's waaaaaaaayyy too much info/work for what the OP wants to do. He's just asking how to swap stocks, not change the whole stock assembly.
Frankh252
Ahhh, my bad. Since I was a kid I've had a bad habit of taking stuff all the way apart lol
ChaseFan9
It's all good, Frank, I think most of us around here have the same "problem". Just curious, Jerry, which stock are you switching out to?
blue109
As long as the Oracle comes with a commercial buffer tube it will swap right in. Good call on the ACS. Awesome stock. One of my favorites.
survivalshop
As long as the Oracle comes with a commercial buffer tube it will swap right in. Good call on the ACS. Awesome stock. One of my favorites.
