Allow it to dry for 24 hours, lightly steel wool the stock when dried to knock down the sheen, and wipe with a clean, dry, lint free rag. Repeat the oil, dry, steel wool, and wiping. The rule of thumb for refinishing this way is once a day for 7 days, and then once a week for 2 weeks, but this is just for best results.
Full Answer
How do you stain gun stock finish?
3 If your stock has really tight grain with small pores, wipe it down with a tack cloth and you’re ready for staining or applying Tru-Oil® Gun Stock Finish. 1 First, remove what’s left of the stock’s original finish with an appropriate stripper (available from any hardware store). Follow the manufacturer’s instructions.
How do you use Tru oil gun stock finish?
1 First, apply Tru-Oil Gun Stock Finish to the entire stock and allow it to penetrate the grain. Don’t rub it in, just let the wood absorb it. When the stock has soaked up all it can absorb, wipe away the excess and let dry for 24 hours ( Read Carmichel’s Tip below).
How many coats of Finish do I need on my Gun stock?
The number of coats needed will vary depending on the grain of your gun stock and the desired outcome wanted. We recommend 4-5 coats for good overall protection. 7 Final Coat - Apply the final coat carefully and sparingly, spreading the oil so there is no streaking. This coat will dry to a rich gloss finish.
How do you Polish a gun stock with Birchwood Casey?
1 Polish with Birchwood Casey Stock Sheen & Conditioner after waiting at least 7 days after applying your last coat of Tru-Oil Gun Stock Finish. Stock Sheen & Conditioner effectively removes any surface imperfections and leaves your stock with a satin finish 2 Repeat applications as desired for a softer matte finish.
Can you refinish a gun stock?
0:5715:45How to Refinish a Rifle Stock - woodworkweb - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd this gun will be completely stripped and we will refinish it completely so that looks almost asMoreAnd this gun will be completely stripped and we will refinish it completely so that looks almost as though it came out of the factory. That what I'm working with today is a single piece of stock.
What is the best finish for a gun stock?
The best finish to put on a gun stock is an oil finish. It is easy to apply, durable and can be used on finished and unfinished wood. Oil finish is also water-proof, prevents UV light from damaging the wood, and can last for several years.
Can you varnish a gun stock?
0:225:49Gunsmithing - Stock Finishing with Bar Top Varnish Presented by Larry ...YouTubeStart of suggested clipEnd of suggested clipIt's a very attractive finish. But bar top finish as a filler is more durable the bar or tabletopMoreIt's a very attractive finish. But bar top finish as a filler is more durable the bar or tabletop varnish will give the stock a very hard and moisture repellant surface when used to fill the grain.
How much does it cost to refinish a gun stock?
Current Refinishing Pricing for most gunstocks: $385 – 445 for most stocks. The amount depends on variables such as type of wood; ease/difficulty of old finish removal; extent and location of dents, gouges, scratches; coats required, etc.
What is satin gun finish?
Satin is designated for the sheen or absense of shine , in the laquer. It usually is in the laquer used 30, 60, 90 sheen used most often. higher the number ,the more lack of a shiny finish will result . Satin finishes are normally left as is when finished spraying (out of gun finish).
What do you seal gun stock with?
0:051:03How to Seal the Wood When Finishing a Gun Stock - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is wood sealer. Apply it liberally and it will penetrate deeply into the wood. This is myMoreThis is wood sealer. Apply it liberally and it will penetrate deeply into the wood. This is my absolute. Favorite part of finishing because you can begin to see the real beauty in the wood.
Is linseed oil good for gun stocks?
Boiled linseed oil is more often used on bare wood and is popular for finishing gun stocks, as the process of heating it decreases its drying time. When hand rubbed into wood, it creates a durable weatherproof seal and the heat produced from the friction of rubbing produces a deep, polished finish.
Can you use Minwax on a gun stock?
0:287:46How To- MinWax Wipe on Poly Gun Stock application Part 4 - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just holding it by the stock. Get the polyurethane rubbed in and then i'm going to do a veryMoreAnd just holding it by the stock. Get the polyurethane rubbed in and then i'm going to do a very light coat i'm probably going to be putting.
Can you stain a gun stock?
2 If the stock is relatively scratch-free, give it a gentle sanding with 120-grit, 180-grit, and finally 280-grit paper and polish with extrafine steel wool. Wipe with a tack cloth and go right to staining or applying Tru-Oil® Gun Stock Finish.
How many coats of Tru Oil are on a gun stock?
Then just oil-dry-buff until you get your desired finish. As little as two coats can make a durable glossy finish, but I like to take it out to 4-6 or even 8 for a deep luster.
How much does it cost to restore an old shotgun?
Base Shop PricesService Charges:PriceRestoration of Modern Guns (Does not include new parts):Bolt Action Rifle or Shotgun$150.00Pump or Auto Rifle or Shotgun$175.00116 more rows
How are gun stocks finished?
7:299:38Finishing a Gun stock with Tru Oil - Complete How To (The ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAfter wet sanding the full strength coat I did an additional three coats on top of it each timeMoreAfter wet sanding the full strength coat I did an additional three coats on top of it each time between coats I would buff it out with triple out steel wool.
What is the slowest finish to remove?
Home-finishes, varnish, polyurethane , even shellac, and factory epoxy are common. Removal time and technique involved varies by the chemical nature of the finish and how strongly it’s bonded to the wood. Polyurethane seems to be the most common and can be the slowest to remove, depending on the manufacturer.
How long does it take for oil based finish to dry?
Sometimes up to 10, even more coats are needed to achieve deep, lustrous beauty. Drying time between coats is at least one day. Drying times also vary, depending on humidity.
What does street value mean on a firearm?
The street value may mean something or nothing to you. As well, an extremely valuable firearm may be perceived of lesser value if modifications, including gunstock refinishing, are made to it. Really, it comes down to whether you want to focus on the collectible dollar value, or re-do the stock and get a look for your own personal enjoyment.
Can you remove gun oil from wood?
Gun oil stains in wood: These are difficult to remove. Many can be removed completely, but not always. The severity and depth of the stain, type of oil that created it, and how long it’s been there are crucial factors. Some oil stain residue simply can’t be completely removed.
Does rubbing oil make wood grain pop?
In so doing, it reveals the true grain inherent in the wood. Rubbing oil penetrates, making the grain ‘pop!’. The penetrating oil also deepens contrast between light and dark wood fibers (grain), revealing the full beauty of the pattern. (And therein lies the ‘rub’ of hand-finishing.
Does refinishing a stock increase the value of a firearm?
Keep in mind refinishing a stock can definitely increase the “perceived value” and even street value of any firearm, simply because it looks so much better. I’m not referring to the collectability value of the firearm here, only to what others may be willing to pay for your gun should you want to sell it.
How to sand a gun stock?
1 Following final tooling on a new gun stock, begin sanding with a medium to coarse paper. 120 is typically enough grit to remove material quickly without being too aggressive. Always sand with the grain whenever using an abrasive.
How to apply Tru Oil gun stock finish?
If darker than desired, sponge wood with clear water. If lighter than desired, add more stain. 4 Allow the Walnut Stain to dry overnight before applying Tru-Oil® Gun Stock Finish.
What is Birchwood Casey Walnut Stain?
Birchwood Casey Walnut Stain is a water-based stain that will produce a clear, rich walnut color without grain clouding or smearing. 1 As a test to determine whether to stain or not, examine a portion of the wood while it is wet with water or alcohol.
How to apply Birchwood Casey Perma Blue?
1 Apply Birchwood Casey Perma Blue® Paste or Liquid Gun Blue with an applicator swab over the entire surface to be blued. Work as quickly as you can, but remember to be thorough. Rather than blueing the entire surface at one time, you may want to divide the work into 2 or 3 sections.
How to keep stock edges sharp?
To keep stock edges sharp and the wood’s surface ripple-free, always sand with a sanding block. The block will prevent the abrasive from “digging in” on soft spots in the grain. And remember to sand AROUND checkering to keep the checkered peaks crisp. Keep checkering masked off until final application of oil.
How to apply Birchwood Casey gun stock sealer?
1 Apply Birchwood Casey Gun Stock Sealer and Filler generously and directly to wood with brush or a clean, lint-free cloth. Do not over brush. Let dry for 60 minutes or until thoroughly dry.
How to apply Tru Oil to a gun?
1 First, apply Tru-Oil Gun Stock Finish to the entire stock and allow it to penetrate the grain. Don’t rub it in, just let the wood absorb it. When the stock has soaked up all it can absorb, wipe away the excess and let dry for 24 hours ( Read Carmichel’s Tip below).