First lightly sand your stock so that you get some sawdust residue, then mix your epoxy with the sawdust until it looks like a glop of gooey wood mud. Use a tooth pick to push your new wood muck into the crack completely, then use a clamp of some sort to push the wood together and hold it there.
Full Answer
Do you remove the stock first when refinishing a rifle?
It is much easier to handle the stock during the refinishing process if it has been taken off first, and this will prevent any accidental damage to the barrel or action as well. After the stock is removed, the most effective way to remove the old finish is to sand it by hand.
How do you stain gun stock finish?
3 If your stock has really tight grain with small pores, wipe it down with a tack cloth and you’re ready for staining or applying Tru-Oil® Gun Stock Finish. 1 First, remove what’s left of the stock’s original finish with an appropriate stripper (available from any hardware store). Follow the manufacturer’s instructions.
What are the typical issues when refinishing a gunstock?
More complicated refinishing issues need to be discussed before we both commit to your gunstock restoration. The usual issues are as follows: Gouges and scratches: that are deep can usually be filled to exactly match the feel and surface level of your stock.
Should I stain my wood stocks?
Sometimes, however, stain should be applied, being needed for enhanced visual effect on dull, non-descript wood stocks. Sometimes a really dull wood appearance can be vastly improved with a little color. I’m glad to help you regarding stain application, from an experience standpoint.
What is the slowest finish to remove?
Home-finishes, varnish, polyurethane , even shellac, and factory epoxy are common. Removal time and technique involved varies by the chemical nature of the finish and how strongly it’s bonded to the wood. Polyurethane seems to be the most common and can be the slowest to remove, depending on the manufacturer.
How long does it take for oil based finish to dry?
Sometimes up to 10, even more coats are needed to achieve deep, lustrous beauty. Drying time between coats is at least one day. Drying times also vary, depending on humidity.
What is essential wood prep?
Essentials are: Thorough wood prep that prepares the wood for a new finish. Selection of finishing oils, hardeners, and drying components to maximize a handcrafted result. Determining the best application technique to achieve the desired finish and high-end outcome. Time.
Can you remove gun oil from wood?
Gun oil stains in wood: These are difficult to remove. Many can be removed completely, but not always. The severity and depth of the stain, type of oil that created it, and how long it’s been there are crucial factors. Some oil stain residue simply can’t be completely removed.
Does rubbing oil make wood grain pop?
In so doing, it reveals the true grain inherent in the wood. Rubbing oil penetrates, making the grain ‘pop!’. The penetrating oil also deepens contrast between light and dark wood fibers (grain), revealing the full beauty of the pattern. (And therein lies the ‘rub’ of hand-finishing.
Does refinishing a stock increase the value of a firearm?
Keep in mind refinishing a stock can definitely increase the “perceived value” and even street value of any firearm, simply because it looks so much better. I’m not referring to the collectability value of the firearm here, only to what others may be willing to pay for your gun should you want to sell it.
How to make a wood stock look like a glop?
First lightly sand your stock so that you get some sawdust residue, then mix your epoxy with the sawdust until it looks like a glop of gooey wood mud. Use a tooth pick to push your new wood muck into the crack completely, then use a clamp of some sort to push the wood together and hold it there.
What to do after stripping stock?
After stripping your stock, it still will have some old stain and grease trapped in its pores. To correct this start boiling some water ( be careful!) then use a de-greaser of your choice. I used "Krud Cutter" because it is biodegradable and it lathers the wood in a nice coat of suds.
How long to boil stock in hot water?
Cover your utility sink with a towel and allow your stock to float in the hot water for about 5 min before flipping it to the other side. Keep doing this until the water is lukewarm.
How long does Tru oil dry on wood?
The first coat the wood should soak up fairly quickly, which is wonderful! Allow the tru oil to dry for 8 hrs. Once you get back from an 8 hour pizza run, be sure to lightly sand the surface with some steel wool, and apply another layer of tru oil.
How to apply Tru Oil gun stock finish?
If darker than desired, sponge wood with clear water. If lighter than desired, add more stain. 4 Allow the Walnut Stain to dry overnight before applying Tru-Oil® Gun Stock Finish.
How to sand a gun stock?
1 Following final tooling on a new gun stock, begin sanding with a medium to coarse paper. 120 is typically enough grit to remove material quickly without being too aggressive. Always sand with the grain whenever using an abrasive.
What is Birchwood Casey Walnut Stain?
Birchwood Casey Walnut Stain is a water-based stain that will produce a clear, rich walnut color without grain clouding or smearing. 1 As a test to determine whether to stain or not, examine a portion of the wood while it is wet with water or alcohol.
How to keep stock edges sharp?
To keep stock edges sharp and the wood’s surface ripple-free, always sand with a sanding block. The block will prevent the abrasive from “digging in” on soft spots in the grain. And remember to sand AROUND checkering to keep the checkered peaks crisp. Keep checkering masked off until final application of oil.
How to apply Birchwood Casey gun stock sealer?
1 Apply Birchwood Casey Gun Stock Sealer and Filler generously and directly to wood with brush or a clean, lint-free cloth. Do not over brush. Let dry for 60 minutes or until thoroughly dry.
How to apply Tru Oil to a gun?
1 First, apply Tru-Oil Gun Stock Finish to the entire stock and allow it to penetrate the grain. Don’t rub it in, just let the wood absorb it. When the stock has soaked up all it can absorb, wipe away the excess and let dry for 24 hours ( Read Carmichel’s Tip below).
How to control the color of walnut stain?
2 Walnut Stain is a concentrate solution; color intensity is easily controlled by adding water. Dilute with water before using to achieve a lighter color; or leave full strength for a darker color. It’s best to test color intensity on a scrap piece of wood. Generally 50/50 stain and water mix works for most situations.
How to remove old finish from rifle?
After the stock is removed, the most effective way to remove the old finish is to sand it by hand.
How to get darker walnut stain?
To get the color that you want, just add water and spot test the stain on a piece of scrap wood until the right consistency is achieved. If you decide you like the darker stain, no water is necessary.
How long to wait to apply Tru-Oil to Birchwood Casey?
After waiting at least 24 hours, use very fine steel wool to lightly remove any dust that may have settled while drying before moving on to the next step. Apply Tru-Oil. Birchwood Casey Tru-Oil is sometimes easier to apply to your rifle stock using bare fingers.
How to fix scratches on a rifle?
Apply Filler. Once you have sanded off the old finish, look for any remaining scratches or gouges. If there are any, fill those in with a wood filler. After letting the filler dry, sand down the spots that have just been filled so that the rifle’s stock is even and smooth. Apply Walnut Stain.
Can you use water to stain walnut?
If you decide you like the darker stain, no water is necessary. For most refinishing applications, a 50/50 water/stain mixture is just about right, but this depends on your personal preference and the original color of the stock. Apply the walnut stain with a clean, dust-free cloth and let it dry overnight.
