Installing a Line Output Converter Step 1 Locate the wires running from the head-unit or factory amplifier to the speakers. In most cases you'll access these wires behind the head unit. Step 2 Once you find the speaker wires, use the wire strippers to remove 1 inch of insulation from each one.
Full Answer
How to install a line output converter?
How to Install a Line Output Converter. 1 1. Disconnect the negative battery terminal. Once you are ready to go, start by disconnecting the negative battery terminal. This step will help keep ... 2 2. Remove your factory head unit. 3 3. Review your wiring diagrams. 4 4. Strip Wires and Make the Proper Connections.
How do I hook up an amplifier to a RCA cable?
Lastly, you will plug in the RCA cables to the line output converter and run and connect the RCA cables to the amplifier. If using the remote wiring you will also need to run that to the amplifier at this time.
How do I know where to connect the wires to my stereo?
Review your wiring diagrams In order to understand where to connect your wires, you will need to ensure you understand your stereo output wiring. Refer to the wiring diagram for your stereo before proceeding to the next step.
How do I hook up an amplifier to a Scosche Loc?
Lastly, you will plug in the RCA cables to the line output converter and run and connect the RCA cables to the amplifier. If using the remote wiring you will also need to run that to the amplifier at this time. On a LOC that uses speaker connector terminals like the Scosche SLC-4, the process will be similar, but with just fewer steps.
How do you install a line output converter to a stock AMP?
0:003:07how to install a loc - line output converter in 3 minutes - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne will be a solid color and one will have the black stripe the solid color will go to the positiveMoreOne will be a solid color and one will have the black stripe the solid color will go to the positive side of the speaker that we're tapping into the one with the black stripe goes to the negative.
How do you set up a line output converter?
6:278:28How To Install a Line Output Converter (LOC) To Any Car (Simple)YouTubeStart of suggested clipEnd of suggested clipWhat you need to do is you need to just run electrical tape around it. So you have a good solidMoreWhat you need to do is you need to just run electrical tape around it. So you have a good solid connection. So it's not going to go anywhere. From there on the backside of the line output converter.
Can you wire SUBS to a stock radio?
Adding a subwoofer to a factory stereo is an excellent method to boost your sound while retaining your factory controls. The nifty devices can produce bass and sub-bass sounds at low frequencies. Thankfully, it's pretty simple to wire one into an existing car stereo system.
How do I set my RCA to factory radio?
0:126:03How to add RCA Pre out adaptor to a factory car radio guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd it's part number pc2 so one and what that is is basically it's got speaker wires on one end withMoreAnd it's part number pc2 so one and what that is is basically it's got speaker wires on one end with an earth and RCA connectors on the other end that you can plug your RCA cables into.
Do you need to ground a line out converter?
Anyways this type of line out converter needs to be hooked up to both constant power and ground in addition to the speaker wire inputs. This system uses a signal sensing input to then provide a dedicated remote output for your amp. If you have a test light or multimeter check that your power connections are correct.
How do you hook up a amp to a factory car stereo?
The best way to connect it to a factory system is to tap into the stereo's speaker outputs for the amp's input signal. Then send the amp's outputs back to the stereo's harness, and on to the speakers through the factory wiring.
Does a Line Output Converter need power?
An Active Line Out Converter is a more advanced version of the standard passive line out converter. These require 12v power to output a signal. These converters also handle up to 400 watts per channel meaning OEM Amplified systems and high powered systems are not an issue.
Do you need a line output converter for subwoofer?
A: Yes, definitely. Amplifiers that offer speaker-level inputs don't require a separate line output converter to tap into existing speaker wires to get their signal. Many powered subwoofers offer this feature, too. The speaker-to-line level conversion is done inside the amplifier.
Do I need to bypass factory amp?
Bypassing the factory amp takes a little more work because you have to run the bypass harness to the factory amp, which is often located in some other part of the car. It's usually worth the extra effort because you'll get better sound from your new stereo, even if you're keeping those factory speakers.
Do stock radios have RCA jacks?
Well, factory stereos don't have something called 'RCA pre-outs'. These are the red and white inputs behind stereos that rca jacks plug into to produce sound… …and factory stereos just don't come equipped with them.
How do you wire a sub to a stock head unit?
3:436:05How to: Add Aftermarket Subwoofer and Amp to Factory Stereo. - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou would run cable that goes from that and plug directly into here I have speaker inputs and so nowMoreYou would run cable that goes from that and plug directly into here I have speaker inputs and so now what that does is it allows you to tap off of a speaker wire.
Where do you connect the remote wire on a stock radio?
2:435:08How to: Wire an amp w/ Stock Radio - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd now they give you a remote out source the remote out wire will plug in to the remote wire inMoreAnd now they give you a remote out source the remote out wire will plug in to the remote wire in your amp. So whenever this line up converter gets a signal.
What is a LOC converter?
The good news is that a LOC, or line output converter, is made for these situations and is an affordable option. These will convert the speaker-level output into an RCA signal, which will allow the connection to an amplifier.
How to connect RCA cables to a speaker?
First, strip the wires from the stereo wiring and then make the proper connections with the corresponding speaker connector terminal. Make sure each wire is secure and the wire is not loose, but do not overtighten it. Then connect your RCA cables to the corresponding places on both your LOC and your amplifier. 5.
Why aren't my factory stereos replaced?
The clean look of a factory stereo, GPS features, and the cost of a new unit are a few reasons they are not replaced. However, many want to upgrade their sound system with an amplifier to provide more power to some aftermarket speakers. Unfortunately, factory stereos do not have the necessary preamp outputs needed that would allow you ...
How to test a new amplifier?
Test your System and Tidy Up the Install. Now that all the wiring is completed, you will want to test your new amplifier. Connect your battery and turn on the stereo to ensure the amplifier, stereo, and speakers are working as expected. Make any necessary adjustments, if needed, and proceed to finalize your install.
How to fix a short on a syringe?
1. Disconnect the negative battery terminal. Once you are ready to go, start by disconnecting the negative battery terminal. This step will help keep you and your equipment safe by preventing shorts, blown fuses, and other electrical problems. 2.
Do factory stereos have preamps?
Unfortunately, factory stereos do not have the necessary preamp outputs needed that would allow you to easily connect an amplifier to it. The good news is that a LOC, or line output converter, is made for these situations and is an affordable option. These will convert the speaker-level output into an RCA signal, ...
Disconnect The Battery
Before starting any electrical job on your car, you should disconnect the battery at the negative terminal.
Remove The Head Unit
Once you have disconnected the negative terminal, you’re good to start and the first thing you should do is remove the factory head unit.
Review Your Wiring Diagrams
At this point you really need to ensure you know which wires are for what, so reviewing the wiring diagram for both your head unit and your LOC is a good idea.
Splice Wires and Prepare To Connect Them
Once you know the wires you’ll be connecting, you need to get your wire strippers and remove about 1 inch from both the Line Output Converter and the wires in your speaker wires in the harness, and your amplifier for the remote turn-on output.
Connect LOC Wires To Head Unit Wires
Once all wires are spliced, you’re ready to connect them. I like to use butt connectors to connect the wires as I think they offer a sturdy connection as long as you crimp them properly. You can solder them if you prefer.
Plug In Your RCA Cables To LOC
Once you’ve connected all wire pairings, you’re now ready to plug your RCA cables from your Line Output Converter to your amplifier. Make sure you put the same connector into the corresponding terminal on each device: + to + terminals and – to – terminals on your LOC and amplifier.
Test Your New Installation
Once you’re all connected up it’s time to test your new installation before putting everything back. Simply re-connect your battery at negative terminal, and switch on your head unit and make sure your speakers and amplifier are working optimally.