Release the retention clips on each side of the heatsink from the motherboard socket mounting lugs. Lightly twist the CPU cooler clockwise and counterclockwise to loosen the seal between the heatsink and the lid of the CPU. Carefully lift the CPU cooler from the CPU. When done correctly the CPU should remain seated in the socket.
Full Answer
How do I install a CPU cooler?
If your cooler you want to install comes with pins like the Intel ones, you just need to "turn left wise" the 4 brackets that hold your cooler just like in the photo showed (red marks). Turn left all 4, then pull them up and release the cooler.
How do I Reset my Intel processor fan push pins?
Resetting Boxed Intel® Processor Fan Heatsink Push Pins. To reset the processor fan push pins, remove the fan and reinstall it as shown below. Remove the fan connector from the fan header. Turn the push pins with a flat bladed screwdriver counterclockwise 90 degrees to release them. Pull up the push pins.
How to remove motherboard from case to install new cooler?
Now if your new cooler has a back, that needs to mount on the motherboard, then you need to remove motherboard from the case. Usually it's 6 screws holding it ( blue marks).
How to remove thermal paste from a CPU?
Remove the old thermal paste from your cpu, using Isopropyl alcohol-recommended- or you can also use <70% acetone if you like. Be careful don't spill it on your motherboard, use a coffe filter to rub gently your cpu.
How do you remove Intel stock cooler?
0:000:50How To Remove an Intel Heatsink and Fan - YouTubeYouTubeStart of suggested clipEnd of suggested clipEach has an arrow on the top rotate each pen 90 degrees in the direction of the arrow. Pull each ofMoreEach has an arrow on the top rotate each pen 90 degrees in the direction of the arrow. Pull each of the pins straight up and you should hear a click as they unlatch from the motherboard.
How do you install a stock Intel CPU cooler?
1:383:21Install an Intel LGA1150 or LGA1155 CPU Processor as Fast As PossibleYouTubeStart of suggested clipEnd of suggested clipMake sure that the plastic pins stick through all four holes in the motherboard. The easiest way toMoreMake sure that the plastic pins stick through all four holes in the motherboard. The easiest way to check this is to rotate the heatsink a little bit and see if all of the pins. Move.
How do you remove a stock cooler from a CPU?
Removing the CPU CoolerRelease the retention clips on each side of the heatsink from the motherboard socket mounting lugs.Lightly twist the CPU cooler clockwise and counterclockwise to loosen the seal between the heatsink and the lid of the CPU.Carefully lift the CPU cooler from the CPU.
Can you remove a CPU cooler and put it back on?
well normally most people will re apply it, but thats because they want the absolute best thermal performance. but if you just took off the heatsink you can put it back with out having to reapply the paste. it wont affect performance if are you just using the computer for normal operations.
How do I replace my Intel CPU cooler?
0:213:35Intel CPU Fan Removal/Install - YouTubeYouTubeStart of suggested clipEnd of suggested clipAny cables that are attached to it there should be either one or two depending on what kind of fan.MoreAny cables that are attached to it there should be either one or two depending on what kind of fan. And then you unscrew the four screws now on a Intel motherboard depending.
How do I install an old Intel CPU cooler?
Place the heatsink-fan combo on top of the CPU. Push down on each of the four locking pins in an X formation (top-left, bottom-right, top-right, bottom-left). Secure the pins by turning them towards the CPU following the small arrows. Plug the fan into the CPU_FAN header on the motherboard.
Can you replace CPU cooler without removing motherboard?
You should be able to install the cooler without removing motherboard. Cutout in the case allows accessing motherboard cpu area from both sides.
Do I need to replace thermal paste after removing heatsink?
How Often Should You Replace Thermal Paste? In most cases, you shouldn't need to reapply more than once every few years, though you should replace your paste if you remove your cooler for any reason. You may also want to consider reapplying thermal paste if you find your CPU temperatures are climbing.
Is thermal paste toxic?
Simply put, thermal paste is not that toxic to cause any harm to humans. The thermal paste contains metal oxides for the conduction of heat. If you consume large amounts of those oxides, they can cause a bit of harm to your body.
Is it OK to leave thermal paste on CPU?
It shouldn't kill your processor but you may loose cooling performance.
Can I reuse thermal paste after removing heatsink?
No. If the cooler has been removed, you need to completely clean both the CPU lid and bottom of the heatsink using isopropyl alcohol and a lint free cloth or coffee filter, and then reapply new paste.
Do you need thermal paste to reseat CPU?
Distinguished. Nope, best not to even try. Good chance you'll just bend pins on the cpu. Thermal paste quality matters little unless you plan to overclock, otherwise just use what you have.
What is the LGA1155 socket?
The LGA1155 socket is shown below with its protective plastic cover removed so you can see the pins which interface with the CPU. LGA1155 CPU Socket (protective cover removed) As you can tell by the photo, these tiny gold pins are very delicate.
Does Intel heatsink come with thermal paste?
This Intel heatsink comes with thermal compound already applied to the base, so we don't need to worry about that. When installing a heatsink, ensure there is always a small amount of thermal paste between the cooler and CPU.
Step 1: Replacing Your Intel Stock Cooler
I will start by saying this is my first instructable, so forgive any mistakes. English is not my mother tongue, so also I am sorry for any grammar mistakes. So you want to change your stock cooler, with something bigger, for overclocking purposes or just for fun. Here are the steps. Open the side of your case (usually 2 screws holding it).
Step 2
If your cooler you want to install comes with pins like the Intel ones, you just need to "turn left wise" the 4 brackets that hold your cooler just like in the photo showed (red marks).
Step 3
Turn upside down your mojo, mount the base that comes with your cooler ( I use Raijintek Aidos).
Step 4
Use the 2 M3 screws carefully screw them equally to hold your cooler in place. Place the 4 anti-vibration mounting arms and slight them in place to hold your fan. Place your fan and mount the four pin socket on your motherboard. Put everything again inside your case, mount everything you removed ( always double check). You're done. If you liked this instructable please vote for me, in the First Time Author Contest..
