Similarly one may ask, how do you hook up subs to a factory radio? Connect the amplifier's +12 volt power cable to the electrical system of your vehicle. Connect the ground from the amplifier to the chassis.
Can you hook up a subwoofer to a stock car stereo?
It is possible to hook up a subwoofer to a stock stereo and with the right equipment, the process isn’t too difficult. You will need an amplifier, subwoofer, amplifier wire kit, and a line-out converter to correctly hook up a subwoofer to your car’s stock stereo system.
How do you hook up speakers to the radio?
We grounded to a seat bolt right here back by the amplifier, and then we grabbed speaker wire signal from the factory radio in the dash, connected that to a line output converter right behind the radio, and ran RCA cables and our blue remote turn on wire from behind the radio, down the driver's side of the vehicle, right back here to our amplifier.
Where to tap into speaker wire for subwoofer?
Generally if tapping into factory wires for a subwoofer, it's best to tap into the rear speaker leads. This mainly comes into play if an aftermarket radio is installed and a high pass filter is set on the front speakers to eliminate some of the bass from the front of the vehicle and of course this would take those lower frequencies away from ...
How do I connect my Loc to my amplifier?
Locate the remote wire on the LOC (it is usually blue) and attach it to the remote wire you just connect to the amplifier. You may wish to splice the wires to join them together effectively (make sure this is done when there is no power running through the wires).
Can you hook up subs and amp to stock stereo?
So now you know – it's definitely possible to install a subwoofer and amplifier to your factory system, and still have it sounding good. If you'd like to know more about how to get a killer system set-up in your car without swapping your stereo, give us a call at 510-527-9888.
How do you hook up an amp to a stock radio?
6:258:28How to install an amplifier to factory radio - YouTubeYouTubeStart of suggested clipEnd of suggested clipPositive and negative is gonna go to the driver side positive negative my two gray solid gray andMorePositive and negative is gonna go to the driver side positive negative my two gray solid gray and gray with the black stripe the one with the black stripe is the one that's negative. So positive.
Can you connect a subwoofer to a radio?
If you are using your subwoofer with a home theater receiver, the connection is simple: Just run an audio interconnect cable like this one from the receiver's subwoofer output to the subwoofer's line input (pictured above). If the subwoofer has an input labeled LFE, use that one.
How do I hook up my amp to my speakers and radio?
10:5015:38Wiring a 2 or 4 channel amp to your stock speaker harness ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou have the option of using a second set of rca's from the rear RCA output to the rear RCA inputMoreYou have the option of using a second set of rca's from the rear RCA output to the rear RCA input you can also just use a single set of RCA.
Can I install a subwoofer with a stock radio?
Adding a subwoofer to a factory stereo is an excellent method to boost your sound while retaining your factory controls. The nifty devices can produce bass and sub-bass sounds at low frequencies. Thankfully, it's pretty simple to wire one into an existing car stereo system.
How do you wire a sub and amp?
1:1614:22How to install an amp and sub in your car | Crutchfield video - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe had an aftermarket stereo that stereo would have RCA preamp outputs already on it that we couldMoreWe had an aftermarket stereo that stereo would have RCA preamp outputs already on it that we could use you know connect RCA cables directly from there run them to the back.
Do you need a separate amplifier for subwoofer?
The short answer is that everyone who wants a subwoofer in their car also needs a subwoofer amplifier. As to whether you need a separate amp for your subwoofer, that depends on the hardware you have and the car audio system that you're trying to build.
How do you hook up a subwoofer to a car radio?
0:553:41Adding a Subwoofer to your Vehicle - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe easiest place to tap into the rear speaker wires was in the - behind the head unit remove. TheMoreThe easiest place to tap into the rear speaker wires was in the - behind the head unit remove. The face and stereo with a few screws.
Can I run a sub without an amp?
In nearly all cases, the answer is yes. Unless you have a system in your car or boat that is already powering a subwoofer, you'll need to find an amplifier that will power your sub. Your head unit will typically provide a low-power signal (RCA output) that can be used for an amplifier to power your subwoofer.
How do you hook up a RCA adapter to a stock radio?
3:386:03How to add RCA Pre out adaptor to a factory car radio guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere we go so what we've done this is your adapter with the RCA s on the end yeah we've crimped inMoreThere we go so what we've done this is your adapter with the RCA s on the end yeah we've crimped in the RCA speaker end we adapt to speaker end into our wires that we've cut and stripped.
What is bridging an amp?
Primarily a live sound term, “bridging” is a means to configure a 2-channel amplifier to drive a single loudspeaker with more power than the two original channels. For example, a 100-watts-per-channel amp may output a single channel of 300 watts after bridging.
Do RCA cables go to input or output?
RCA cables are used for connecting to RCA inputs and outputs. The most common example is a stereo RCA cable sending 2-channel analog audio between devices – like from a CD player to an amplifier.
Do I have to use both voice coils on subwoofer?
No, in most cases using one voice coil is fine although you'll get the most performance by using both. Dual voice coils offer more power handling,...
How do you wire a dual voice coil?
To wire a dual voice coil be sure to observe speaker terminal polarity and wire both coils the same way. For series connections, connect the coils...
Can you wire a single voice coil sub to a dual voice coil?
Yes, various speaker impedance Ohm loads can be achieved by wiring single and dual voice coil subwoofers together. Connect them the same way as sin...
What is the difference between a car stereo and a home stereo?
Home stereos, on the other hand, have higher voltage available and can use a higher speaker impedance (8 ohms, typically).
Why do you wire speakers in parallel?
Because of how they work, you’ll get the most power from your amp and to each speaker when they’re wired in parallel. Parallel speaker wiring is generally best for audio speaker systems like in the car or home.
Can you use two voice coils on a subwoofer?
Dual voice coil subwoofers can be used with one or both of their voice coils, although you won’t be able to drive with the same amount of power as you could using both voice coils. They can also have somewhat different behavior and lower heat handling depending on the design when using only one set of speaker terminals.
Do you run the amp wire to the negative wire?
Run the amp’s negative wire to the negative wire of the second set. In both cases, with dual voice coil speakers, it’s extremely important to use the same speaker wire polarity. That’s because the magnetic field polarity – and which direction the voice coils will try to move the speaker – are directly related.
Is there a free lunch on speaker wiring?
It’s important to understand that there’s no “free lunch” as the expression goes when it comes to speaker wiring, amp power, and speaker power. There’s only so much power or heat an amp can produce or handle. It makes a big difference how you wire your speakers to your amplifier or car stereo.
Can you wire subwoofers to the same ohms?
Wiring the subwoofers in a way that’s the best available option for power and at the same or higher Ohms rating, the amp is rated for. Sometimes it doesn’t work out for the best amplifier power if you’re trying to use subwoofers that can’t be wired to the same min. Ohms rating as the amp for its maximum power output.
Why add a subwoofer to a car stereo?
Adding a subwoofer to your factory stereo is a great way to improve your sound without giving up your familiar factory controls. In this video, you can follow along as one of our experts installs an amplifier and subwoofer in a car with a factory stereo. You'll see all the basics of amplifier installation, including:
Can you drive a subwoofer without an amp?
If you intend to drive that subwoofer without an amplifier and it's not a powered sub, that won't work. Your radio or even factory amp isn't going to be able to do it. And underpowering will be detrimental to the sub and whatever is underpowering it.
