Do this by connecting the radio’s amplifier remote turn on wire to the DSR1 solid blue wire (remote in). Some aftermarket radios will have both a blue wire and a blue/white stripe wire. If this is the case, the proper wire to use is the blue with white stripe wire.
How do you wire a car radio remote turn on?
Simply connect another piece of blue primary wire to the blue wire in the wiring harness and run the primary wire back to the amplifier to terminate in the remote turn on terminal. To connect wire to wire, an appropriately sized butt connector or other style connector can be used.
Can a remote turn on radio be connected to any fuse?
Since the remote turn on wire is low current, it can be connected to almost any fused output terminal (such as the one for the radio itself) as long as it only powers up when the vehicle is on. (To make sure you choose a fuse that only receives voltage when the ignition is on, you can test with a multimeter before connecting the wire.)
How does the remote turn on wire work?
The remote turn on wire receives voltage from the factory electrical system when the ignition is in the ACCESSORY or ON position (keep reading this document for the complete explanation).
How do you test the ignition remote turn on wire?
Be sure the positive lead is touching the wire strands inside the jacket of the remote turn on wire. With the ignition in the OFF position, there should be no voltage. Then turn the ignition to the ON position and test the same way again. While in the ON position, there should be 12+ volts at the remote turn on wire.
Where do you connect the remote wire on a stock radio?
2:275:08How to: Wire an amp w/ Stock Radio - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd now they give you a remote out source the remote out wire will plug in to the remote wire inMoreAnd now they give you a remote out source the remote out wire will plug in to the remote wire in your amp. So whenever this line up converter gets a signal.
How do you wire a remote to a radio turn?
1:185:02What is an Amplifier Remote Turn-On Wire? - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're just going to wire up color for color here you're going to go blue with white to blue withMoreYou're just going to wire up color for color here you're going to go blue with white to blue with white it's your simple just connection made for your patent for your amplifier.
Where is the remote wire in my car radio?
2:003:32Finding the remote wire. Works for any car. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSee the car is turned on and if. I put this positive side in there see the light turn on. It. MeansMoreSee the car is turned on and if. I put this positive side in there see the light turn on. It. Means that's my remote fire. And that's what I lost my car same spot right there.
What color is the remote wire on a radio?
Wiring Harness Color StandardsWire ColorWire FunctionRedSwitch / AccessoryBlackGroundBlueAntenna RemoteBlue with White StripeAmplifier Remote Turn-on10 more rows
Can you run remote wire with power wire?
Power wire + speaker wire is high level. Run them together if you want. Power wire + RCA is the "bad" one (and even that's debatable...). Remote can go just about anywhere.
What fuse do I connect the remote wire to?
You should be using a fuse tap that will add a fuse for the remote turn on wire in addition to the OEM fuse on the circuit. A 1 amp fuse is enough for your remote lead.
Can I use speaker wire for remote wire?
you can use speaker wire for that. Just run the remote wire off your other amp. any copper wire will work it doesnt matter how old or new it is. just find some old copper wire and use it.
How do I turn on my amp without remote wire?
1:302:51How Can I Turn On My Amp Without Remote Wire? | Car Audio Q & AYouTubeStart of suggested clipEnd of suggested clipFrom your ignition switch to your amp that will turn the amplifier on and off with the key. Or yourMoreFrom your ignition switch to your amp that will turn the amplifier on and off with the key. Or your radio might depending on the vehicle.
What is the blue wire on a car stereo?
Ground wires are black, antenna wires are blue, and amplifier wires are blue with a white stripe.
Why is my remote wire not working?
The power wire is the next thing to check if you find no problems with the remote wire. This wire is thicker than the remote wire, and it should have battery voltage. If it doesn't, check for any inline fuses and verify that the wire isn't loose, corroded, or shorted out somewhere.
What's the yellow wire for on a car stereo?
The yellow wire is the 12 volt battery wire, which should also be attached to the stereo for power. The final wire, the black wire, is the ground wire. This wire, once attached to the stereo, will help ground it.
Where do I connect the blue remote wire?
AFTERMARKET HEAD UNIT Simply connect another piece of blue primary wire to the blue wire in the wiring harness and run the primary wire back to the amplifier to terminate in the remote turn on terminal. To connect wire to wire, an appropriately sized butt connector or other style connector can be used.
Answers
Yes there are several ways, you can get one of the KASA or WEMO or many others devices and a DLI relay that you connect to the Remote ON/OFF connection on the back of the radio.
Leave a Comment
Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu.
Answers
The radio has to be on and fully booted up for the remote option to work. When you tell the radio to turn off remotely it is not fully powered down as it has to watch for a turn on command and if you have a GPS it keeps it alive as well. Thus turn on the Power Supply first, wait a few minutes then use the remote port to wake up the radio.
Leave a Comment
Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu.
How to use an aftermarket radio?
When using an aftermarket radio it is critical that you use the amplifier remote turn on wire (usually blue or blue with white stripe) to trigger the DSR1. Do this by connecting the radio’s amplifier remote turn on wire to the DSR1 solid blue wire (remote in). Some aftermarket radios will have both a blue wire and a blue/white stripe wire. If this is the case, the proper wire to use is the blue with white stripe wire. The solid blue wire on these radios is for a power antenna and will not provide 12 volts unless in Am/Fm mode (not good!).
What happens if the remote turn on wires are not connected properly?
So if the remote turn on wires are not connected properly as shown above, you can almost guarantee a nasty turn on pop will occur.
How much does a TR4 cost?
A TR4 can be purchased for $18 (Shipped) if you need one. Just give us a call 1 (916) 823-5256. Connect the Green wire to the DSR1 remote out wire (blue/white) and the blue wire of the TR4 to the amplifier (s) remote input wire. Tag positive and ground (yellow & black) directly from the DSR1 power black and yellow power wires.
Why does my bike turn off pop?
Turn off pop happens when there is a difference in ground potential between the amplifier and other devices in the system (radio and or DSP). The first thing to check is that the amplifier and DSP are both grounded directly to the battery and never the bikes frame.
Do you fuse the yellow wire on a DSR1?
Be sure to fuse the yellow wire if you are getting power for the DSR1 from the amplifier power terminals. This will add an additional single second to the power up time of the amplifier. By this time all popping devices on the bike should be done doing their thing and the electrical system will once again be silent.
Can you connect a DSR1 radio to a blue wire?
Most radios will have a Blue/white wire. Never connect the radios Blue/white wire to the DSR1 blue/white wire. This will destroy the power supply of the DSR1 and potentially the radio. This is not covered under warranty.
