How do I replace the stem on my PS pump?
Use your file to take about 1/8" off the pin end of the stem (this is precautionary - to prevent the bypass from jamming shut). Drop in the spring, the seat/stem, the BB, and replace the top nut. Reinstall the large spring, the cartridge, and the 1" nut back into your PS pump.
What's wrong with my stock steering pump?
The stock Toyota pump is just barely able to supply the volume and pressure needed to run Hydraulic assist steering. The stock pump puts out 1,300 PSI at only one gallon per minute. The stock pump is not able to provide enough fluid to run both the stock steering and the demands of a ram, especially at low RPM's.
Can I run a full hydro RAM with a stock pump?
Well I run full hydro, single ended ram with a stock pump and so far have not had any issues other than it leaking out of the cap on angles.. i have just drilled out the outer plug for more flow. Won't have any real world results for atleast a week. I also am looking forward to learning more on this.
How do you drill out a broken bolt?
Using a hammer, mark the center of the broken bolt with a center punch. This will help you drill into the center of the bolt as closely as possible, putting you at less risk of damaging the threads of the broken bolt. 2. Drill a pilot hole into the center of the broken bolt with the left-handed drill bit.
How do you tap a power steering pump?
2:229:15How to tap steering box for hydraulic assist - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut some grease on the tap so it'll collect all the metal shavings when you're tapping the hole thatMorePut some grease on the tap so it'll collect all the metal shavings when you're tapping the hole that way it won't you minimize the most amount of trash in there as possible.
How do you tap a Toyota steering box?
1:0217:17Hydro Assist- Drilling and Tapping a Toyota Steering Gear Box - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're going to start at the sector chef mark the box itself. And the gear get us underneath connectsMoreWe're going to start at the sector chef mark the box itself. And the gear get us underneath connects we marked the input shaft at the housing of the gearbox in the shaft itself.
How do you drill and tap a power steering box for hydro assist?
10:0128:23Tap your Steering Box for Hydro Assist - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo in the center of this machine flat right here I went ahead and put a dimple to keep the drill bitMoreSo in the center of this machine flat right here I went ahead and put a dimple to keep the drill bit from walking. And that's where the left-turn port is going to be. If you look inside here.
How do you rebuild a Toyota steering box?
2:5912:32Steering Gearbox Rebuild- Toyota - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo here's how this should have gone power piston nut comes out and a spring and you got your powerMoreSo here's how this should have gone power piston nut comes out and a spring and you got your power piston plunger. And you got your power piston guide.
What is Hydro Assist steering?
The concept behind a hydro-assist kit is that it removes much of the mechanical strain and force from your steering gearbox by placing a hydraulic cylinder at the axle. As you steer the vehicle one way or the other, the cylinder helps push/pull the tie-rod, taking much of the load off of the steering gear.
How do you install hydro assist steering?
0:188:58Hydro Assist Steering Install | 1st Gen 4Runner - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe in the engine bay is already set up to be able to push these things and so what they do is theyMoreThe in the engine bay is already set up to be able to push these things and so what they do is they tap the box we run additional lines down to a hydraulic ram that's down on your axle.
How do you rebuild a steering gearbox?
15:4123:22Rebuild your Steering Gear Box - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you have a flat bearing and and washer on the bottom side of that bearing make sure that those goMoreIf you have a flat bearing and and washer on the bottom side of that bearing make sure that those go back in in the same direction that you took them out.
How do I adjust my steering box?
2:153:30How To Tighten your Steering Box - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow what you're going to do is tighten this clockwise to the right just a little bit probably anMoreNow what you're going to do is tighten this clockwise to the right just a little bit probably an eighth of a turn to start off with right about there and then you're going to tighten. The nut back up.
How do you remove the 80 series power steering pump?
2:3023:4980 Series Land Cruiser Power Steering Pump ReplacementYouTubeStart of suggested clipEnd of suggested clipI just have a crappy crows foot extension piece that goes on to a ratchet does actually work andMoreI just have a crappy crows foot extension piece that goes on to a ratchet does actually work and pretty much go in from this angle and turn it.
How to drill a broken bolt?
1. Center punch the broken bolt as close to the center as possible. Using a hammer, mark the center of the broken bolt with a center punch. This will help you drill into the center of the bolt as closely as possible, putting you at less risk of damaging the threads of the broken bolt. 2.
How to get a broken bolt out of a spherical cylinder?
1. Center punch the broken bolt as close to the center as possible. Just like you would using the extractor, you want to use a hammer and a center punch to mark the center of the bolt. 2. Drill out the center of the bolt. Use a bit that is roughly one-quarter the diameter of the bolt and drill it out.
How to remove a broken bolt without welding?
If you want to remove a broken bolt without welding, center punch the broken bolt, then drill a pilot hole into the center of it with a left-handed drill bit. Next, put an extracting bit into the hole you just drilled and rotate it counter-clockwise until it tightens and unscrews the bolt.
How to attach a hex nut to a bolt?
Thread a hex nut onto the bolt. With any threading the bolt still has exposed, tighten a hex nut onto it. You want to attach the nut firmly , but back it off around half a turn, so that it’s not completely flush with the surface into which the bolt is embedded. 4. Weld the bolt to the nut.
What drill bit to use for a broken bolt?
Drill a pilot hole into the center of the broken bolt with the left-handed drill bit. A left-handed drill bit is threaded in the opposite direction, so the reverse setting on your drill is what will actually drive in the bit. You want to use a left-handed bit because it will torque in the opposite direction as the broken bolt, ...
What to do when removing a broken bolt?
If you plan to replace the broken bolt with a new one, it is important to first remove all of these fillings and shaving. You can most easily accomplish this with either a magnet or compressed air.
Can you break an extractor off a bolt?
Go slow when using an extractor and don’t overpower it. Breaking an extractor off in a broken bolt requires an even stronger material than the hardened steel of the extractor to remove.
How to stop a pulley from turning?
Loosen the pulley nut. Do whatever you can to stop the pulley from turning, then use a tool such as a socket or ring spanner on the nut until the pulley can be removed. Pry off the pulley. Place a pry bar or a large screwdriver behind the pulley, if there is a surface behind it to use as leverage.
How to adjust a gear puller?
Fit the arms. Once the gear puller is set, the center bolt should engage the pulley shaft in proper alignment to prevent slippage. Adjust the arms so that the puller’s jaws are set at about right angles against the pulley or gear. ...
How to get rust off a pulley?
1. Apply penetrating oil. Put this directly onto the pulley and shaft area to loosen any corrosion that will make the pulley hard to move.Those that come in spray bottles are handy and will still be effective for getting into and breaking up rust on metal. ...
Where is the shear key on a lawnmower?
Tips. Lawnmowers have a "shear" key, which prevents damage to the crankshaft, located in the hub of the flywheel or magneto. These often cause the engine to refuse to run but are easily replaced when you learn how to remove them. Thanks!
How to remove a key from a car?
You can also use a gear puller to remove the key. Adjust the arms so its jaws are at right angles against the pulley or gear. Tighten the forcing screw until the pulley slides free and you can locate the key. Then, remove it with pliers.
