Bedding the Rifle Stock
- Mix the bedding compound. Retrieve a non-waxed plastic cup and a popsicle stick. Use the popsicle stick to place...
- Insert the action and tighten the screws. Place the action into the stock. Retrieve a screwdriver. Insert the action...
- Place the vise around the barrel and allow the epoxy to cure. Remove the vise from the stock. Insert the...
Full Answer
How do you fix a bedded rifle stock?
Sep 04, 2013 · Glass bedding is a major component of the ultimate bedding package for rifle accuracy. Larry Potterfield, Founder of MidwayUSA, demonstrates glass bedding a ...
What is bedding a rifle stock?
How To Glass Bed Your Rifle - by Randy Boyd. When you fire your rifle, an upward motion of the barrel is created which causes a pulling action on the stock. Dependent on the caliber, this can be quite violent. If your action isn’t bedded firmly into the stock, this movement can create the opportunity for your barrel and stock to collide, changing the point of impact on your shot.
What does it mean to bed a rifle?
Jul 15, 2012 · Usually, a spoonful of each part mixed together is enough to bed an entire rifle in the manner described. It is a good rule of thumb when mixing the compound to have too much rather than not...
How can I make my rifle’s stock fit better?
To “bed” a rifle means to precisely fit the stock around the action (and sometimes the barrel, too). Two-piece stocks mount onto the firearm, rather than supporting the firearm as one-piece stocks do, so bedding is generally only useful (or possible) with one-piece stocks. The purpose of bedding is to tighten the imperfect fit between stock and action, which would otherwise allow …
How to order action for rifle?
Order the correct action for your rifle. Contact the manufacturer of your rifle. Work with a company representative to determine the type of action you require. Place an order for your rifle’s action and wait for it to arrive. The action is the part of the rifle that loads, fires, and ejects the cartridge.
How to make a peanut butter stock?
Mix the bedding compound. Retrieve a non-waxed plastic cup and a popsicle stick. Use the popsicle stick to place equal parts resin and hardener into the plastic cup. Add dye to the mixture so that it matches the color of the stock. Use the stick to stir the mixture until it is a peanut-butter like consistency.
How to ensure action feeds correctly?
To ensure that the action feeds correctly, place dummy shells into the magazine. Do not force the pieces to fit together properly. If the action or another piece does not sit correctly in the gun, contact the manufacturer and order a new part. ...
How to apply release agent to rifle?
Apply release agent to the rifle’s metal parts. Put on rubber gloves before coating the action and barrel with a release agent. Be sure to coat the action screws, foot plate, and every part that will be reinserted into the stock. Allow the release agent to dry. There are several release agents on the market.
How to make a stock with a popsicle stick?
Retrieve a non-waxed plastic cup and a popsicle stick. Use the popsicle stick to place equal parts resin and hardener into the plastic cup. Add dye to the mixture so that it matches the color of the stock.
How to remove epoxy from stock?
Remove excess epoxy with a cotton swab and razor blade. Once the action is screwed into the stock, epoxy seep through the seams. Wipe off any excess epoxy with a cotton swab. Go over the surface with a razor blade to scrape off any remaining residue.
How to remove stock from action?
To remove the stock from the action, unscrew the action screws, remove the bottom metal, and tap the action with a block of plastic. This causes the stock to pop off. With the action out of the stock, a milling machine, with a sharp 1/4″ end mill cleans up the surfaces.
What is the use of a razor blade?
A razor blade is used to trim the excess clay. With the voids filled, its time for another coat of release agent. Any areas that were handled, or came into contact with the clay or razor may have lost their coating. A second application ensures everything will come apart when the epoxy dries.
Does painter's tape fit against recoil lugs?
The painter’s tape will now perfectly fit against the front edge of the recoil lug. With the action degreased and taped, I take the time to make sure it still fits into the stock. In some stocks, the sides of the lugs do not have a lot of clearance, adding the thickness of the tape will prevent the action from seating.
Do Boyds stock have a free floated barrel?
Boyds stocks are meticulously engineered and machined from the most stable materials to maintain a free floated barrel to reduce the opportunity for collision between the barrel and stock. However, in some cases it’s recommended to bed your action. First would be in heavy magnums or firearms with excessive recoil.
What happens when you fire a rifle?
When you fire your rifle, an upward motion of the barrel is created which causes a pulling action on the stock. Dependent on the caliber, this can be quite violent. If your action isn’t bedded firmly into the stock, this movement can create the opportunity for your barrel and stock to collide, changing the point of impact on your shot. ...
Why do stock bedded?
There are many reasons a stock needs to be bedded, an upgrade to a synthetic or nicer wood stock, to improve accuracy or, in this case, the original stock was broken.
Where to put bedding on a Model 70?
This synthetic stocked Model 70 requires bedding in the tang area as well as the front receiver ring. Keeping the stock that’s being replaced and referring back to it will give you an idea where the bedding compound should be placed.
What does it mean to bedded a rifle?
To “bed” a rifle means to precisely fit the stock around the action (and sometimes the barrel, too). Two-piece stocks mount onto the firearm, rather than supporting the firearm as one-piece stocks do, so bedding is generally only useful (or possible) with one-piece stocks. The purpose of bedding is to tighten the imperfect fit between stock and action, which would otherwise allow the action to shift imperceptibly in the stock under recoil. Rifles that are not bedded are constantly enduring these slight changes in position, resulting in inconsistent flexing and vibration shot-to-shot, which in turn translates to less consistent groups and accelerated wear on the stock.
What happens if you don't bedded your rifle?
Rifles that are not bedded are constantly enduring these slight changes in position, resulting in inconsistent flexing and vibration shot-to-shot, which in turn translates to less consistent groups and accelerated wear on the stock. This article focuses primarily on bedding the action. For more details on the considerations for bedding the barrel, ...
Do shooters leave pillars floating in stock?
Others argue that the process demands shop equipment to ensure consistency of angle and diameter. Some shooters leave the pillars floating in the stock, while others will epoxy the pillars in place, sometimes cutting grooves in the outside of the pillar to increase contact area with the epoxy.
What is the purpose of bedding?
The purpose of bedding is to tighten the imperfect fit between stock and action, which would otherwise allow the action to shift imperceptibly in the stock under recoil.
What is the simplest form of bedding?
Below are overviews of the more common types of bedding, along with popular materials and guidelines for use. Shim bedding. Shim bedding is the simplest form of bedding, and involves placing metal or plastic shims in the action and/or magazine inlets in the stock. Placing shims between the action and the stock spreads out the pressure ...
What is shim bedding?
Shim bedding is the simplest form of bedding, and involves placing metal or plastic shims in the action and/or magazine inlets in the stock. Placing shims between the action and the stock spreads out the pressure of the action bolts more evenly, and prevents the action from digging into the softer wood or plastic of the stock.
What is a shim in rifles?
Shims are generally stamped or cut to fit the stock inlet of a particular rifle, but simple steel washers from any hardware store have been used with some success. In pillar bedding, the holes for the action screws are bored out and a hollow metal tube or “pillar” is inserted in the now-oversized action hole.
