Yes, the switch mounting screw is 6/32 machine screw. The 3/8" length sounds about right. If you want to try adjusting a bridge pickup very low (I don't normally but some do), you may need more margin than 3/4" will give you.
Full Answer
What size screws do I need to mount a Tele Bridge?
1 inch long #6 wood screw with an oval head is the Fender spec for mounting a vintage style Tele bridge. A Sheet metal screw will work equally well, and a flat head instead of an oval head can make it easier to get your 5th and 6th string saddle back closer to the bridge bottom.
How do I adjust the pickup height on a Telecaster?
Pickup height adjustment is usually a pretty simple task on a telecaster. The neck pickup is usually attached to the pickguard by 2 height adjustment screws and the bridge pickup is attached to the bridge plate with 3. These are used to change the height of the pickup in relation to the strings to achieve the best tone.
Where are the adjustment screws on a Tele neck pickup?
First, don’t be confused by the typical lack of adjustment screws showing on the Tele neck pickup, simply remove the pick-guard and you will find them hiding beneath!
How do you adjust the height of a guitar saddle?
Using the proper screwdriver or allen wrench, rotate the small height adjustment screws that are threaded into the saddle to raise or lower it. Using a ruler or a string action gauge card and holding the guitar in playing position, measure from the top of the 12th fret to the bottom of the string.
How high should the action be on a Telecaster?
ACTIONNeck RadiusString Height Bass SideTreble Side7.25" 9.5" to 12" 15" to 17"5/64" (2 mm) 4/64" (1.6 mm) 4/64" (1.6 mm)4/64" (1.6 mm) 4/64" (1.6 mm) 3/64" (1.2 mm)
How do I set up my Telecaster properly?
8:0049:59FENDER TELECASTER (TELE) - How to Setup your Guitar, Step-by-StepYouTubeStart of suggested clipEnd of suggested clipSo the way that i'll use this is i'm going to fret my low e string at the 12th fret and i've nowMoreSo the way that i'll use this is i'm going to fret my low e string at the 12th fret and i've now created a straight edge between the first fret and the 12th fret using the low e string. So i can look
How high should Pickups be on Telecaster?
We start with the pickup about 3/32″ from the strings, when the strings are held down at the highest fret. But you'll probably need to adjust it up and down to find the best combination of output, openness, and sustain.
How deep should the neck pocket be on a Telecaster?
5/8″ deepA Fender-style neck pocket such as those found on a Telecaster or Stratocaster is typically 5/8″ deep. Read on to find out why, and what to do for different types of bridges and also non-bolt-on neck types.
How do you adjust the neck on a Fender Telecaster?
5:116:55How To | Truss Rod Adjustment | Fender - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe truss rod which will bring the strings closer to the top of the fretboard. And if the stringsMoreThe truss rod which will bring the strings closer to the top of the fretboard. And if the strings are already too close to the fretboard I'm going to go counterclockwise. And that will loosen.
How do I set up Telecaster intonation?
Setting Intonation on a TelePick the open string and verify it's in tune.Fret at the 12th fret and pick this note. ... If the 12th fret note is flat, move the saddle forward a little by turning the adjustment screw at the back of the bridge (counter-clockwise) using a flat or philips screwdriver (whatever is appropriate).More items...•
How do I know if my pickups are too high?
Setting your pickup height too high will cause your magnets to push and pull your strings out of tune. Here's a quick way to tell if this is happening to you: play the Low E string at a high fret (15th fret is a good one to start at). You might hear a “warbling” sound. That sound is your magnet fighting your string.
Does pickup height affect tone?
Guitar pickup height affects tone due to the distance between the pickups and the guitar strings. As the distance gets smaller, the string's vibration pattern, pitch, and sustain are altered along with an increase in the pickup output. All of these factors ultimately affect the tone of the guitar.
How high should neck pickups be?
We recommend between somewhere close to 5/64" on the bridge pickup, and about 4/64" on the neck. Keep in mind, these are measurements on the Low-E side. On the High-E, we might suggest you move it just a tad closer (say 1/64" on each pickup). Adjusting height is easy.
How do you route a Telecaster neck pocket?
1:032:24Routing a Fender-style neck pocket - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd make your first. Cut. Now I'll remove my shims. And lower the bit another quarter-inch for myMoreAnd make your first. Cut. Now I'll remove my shims. And lower the bit another quarter-inch for my second pass. For the last pass the pocket is deep enough for the bearing to contact the walls.
How deep is a Telecaster control cavity?
Neck Pickup Cavity Depth: 3/4" (1" for some aftermarket pickups) Bridge Pickup Cavity Depth: 7/8" (1" for some aftermarket pickups) Switch/Volume/Tone Cavity Depth: 1 1/2"
Can you put a 22 fret neck on a 21 fret Strat?
It doesn't matter between 21 and 22. 22 fretters just have the last fret overhang so it doesn't move the bridge or mess with scale length or intonation at all. this. except i think warmoth necks have a slightly different neck pocket designed to only fit their bodies, as they are not built to be replacement parts.