Soak the trailer axle and spindle nut in kerosene Use a small pan and fill the bottom with 2 to 3 inches (5.1 to 7.6 cm) of kerosene. Set the greasy axle and spindle nut into the kerosene and let them soak for about 10 minutes.
Full Answer
How do you Grease trailer bearings?
Greasing, or repacking, trailer bearings is an important part of trailer maintenance, and thankfully it doesn’t take long to do! Remove the wheel and take apart the hub until you can access the bearings. From there, you’ll clean them and repack them with new grease. Reassemble the hub and replace the wheel before moving on to the next one.
How often should you Grease the axles on a trailer?
Axles If your trailer’s axle (s) are equipped with a grease zerk on the ends, the bearings must be greased every six months or 6,000 miles to ensure functionality. To apply the grease, remove the rubber plug from the axle end and place the grease gun on the zerk. Pump grease until new grease begins to appear.
How do you Grease bearings on a Dexter Axle?
Carry-On Trailer uses Dexter axles for our trailers, and their recommendations for hand-packing bearing grease are as follows: Place grease into the palm of your hand. Press a section of the widest end of the bearing into the outer edge of the grease closest to your thumb, forcing the grease into the interior of the bearing.
Why do I need to lubricate my Trailer’s axles?
Proper lubrication helps maintain functionality and reliability of your trailer’s axle (s). Bearings should be lubricated approximately every 12 months or 12,000 miles unless otherwise specified by the axle manufacturer. Carry-On Trailer uses Dexter axles for our trailers, and their recommendations for hand-packing bearing grease are as follows:
How do you grease a trailer axle?
0:000:52How to grease your trailer axles - YouTubeYouTubeStart of suggested clipEnd of suggested clipCap you put the nozzle of the grease gun on the zerk. And start pumping while gently spinning theMoreCap you put the nozzle of the grease gun on the zerk. And start pumping while gently spinning the wheel. You need to be pumping gently.
Do you need to grease trailer axles?
Axles. If your trailer's axle(s) are equipped with a grease zerk on the ends, the bearings must be greased every six months or 6,000 miles to ensure functionality. To apply the grease, remove the rubber plug from the axle end and place the grease gun on the zerk.
How do you grease bearings on a horse trailer?
11:0414:57Keeping Your Wheel Bearings Packed & In Good Order - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut your little top topper on. It. Then all you gotta do is give it a push. Just like that see allMorePut your little top topper on. It. Then all you gotta do is give it a push. Just like that see all those little. Degrees so you can see it's injected it from the back. Side. It's went all the way.
How often should trailer axles be greased?
When Should You Grease Your Bearings. With a larger travel trailer, you should grease your trailer wheel bearings every 10,000 miles or once a year, whichever comes first. If you have a smaller travel trailer, however, you'll need to grease your wheel bearings every 2,000 miles.
How do I know if my trailer bearings need grease?
If noise is heard, check for a bad bearing or if lubrication is needed. Check for Heat – Tow the trailer for a short distance, 5-10 miles at highways speeds, then park the trailer. Place your hand on each of the wheel hubs of the trailer. If it is too warm to hold your hand in place, you may have a bad bearing.
How much grease should I put in my trailer axles?
For traditional greases (NLGI Nos. 1 and 2), pump a ring of grease into the entire circumference of the wheel hub and coat the hub cap inner wall. The housing should only be half full of grease. Too much grease causes churning and higher temperatures.
How often should you repack bearings on a horse trailer?
It is recommended by trailer manufacturers to repack your horse trailer bearings every 12 months or 12,000 miles. In any case, wheel bearing maintenance frequency depends on trailer type, wheel size, and average loading weight.
Can you over grease wheel bearings?
Adding too much or too little grease is one of the most common mistakes made in our industry. As we've discussed already, too much grease builds up and eventually causes increased friction and pressure, and that causes excess heat. Too little of grease has the same life-shortening effect on bearings too.
How do you lubricate wheel bearings?
0:307:15How To Grease Wheel Bearings - 2 Easy Methods - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just put some grease in the palm of your non-dominant. Hand now take the bearing and you'reMoreAnd just put some grease in the palm of your non-dominant. Hand now take the bearing and you're gonna press it in. So when you get these wheel bearings you need to grease these.
Should you grease the ball on a trailer hitch?
You do not need to grease your trailer hitch ball. That is entirely up to you. However, greasing it is recommended. Greasing will help ensure that the trailer hitch ball keeps its structural integrity, and it will help prevent it from squeaking.
How do you put grease on trailer bearings?
10:0614:54how to properly grease and maintenance a trailer axle - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'll show you what I did here. I just took a couple paper towels stuck them in that hole and laid aMoreI'll show you what I did here. I just took a couple paper towels stuck them in that hole and laid a couple on the ground so catch that grease didn't want that grease girl on the ground. So now we're
Do you have to grease sealed wheel bearings?
0:235:50HOW-TO Grease A Sealed Bearing - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo usually when you buy a new seal bearing there will be some grease in there however over time theMoreSo usually when you buy a new seal bearing there will be some grease in there however over time the grease does sometimes disappear.
How to grease a roller bearing?
Place grease into the palm of your hand. Press a section of the widest end of the bearing into the outer edge of the grease closest to your thumb, forcing the grease into the interior of the bearing. Repeat the process while rotating the bearing from roller to roller .
How to apply grease to a zerk?
To apply the grease, remove the rubber plug from the axle end and place the grease gun on the zerk. Pump grease until new grease begins to appear. (TIP: Use a different color of grease with each application so it will be easier to see when the new grease appears.)
How to keep a trailer from rolling?
Chock the wheels first by setting heavy wedge-shaped blocks in front of each one to keep the trailer from rolling while you’re working on it. Place a jack stand on either side of the wheel and crank them up until the wheel is no longer touching the ground.
How to remove lug nuts from trailer?
Loosen the lug nuts and remove the wheel from the trailer. Use a wrench or a tire iron to remove the lug nuts and set them off to the side somewhere safe. Pull the wheel off of the rod toward your body and put it off to the side, too.
How to clean a kerosene bearing?
Wipe down the clean bearings and spindle nut with brake cleaner. Take the bearings and spindle nut out of the kerosene and set them on a clean rag or newspaper. Spray them with brake cleaner and either dry them off with another clean rag or let them air dry. This step just helps get the bearings and spindle nut extra clean.
Do trailer bearings need to be lubricated?
They need to be lubricated regularly so that they operate at their best capacity. Greasing, or repacking, trailer bearings is an important part of trailer maintenance, and thankfully it doesn’t take long to do! Remove the wheel and take apart the hub until you can access the bearings.
Do all trailers have a nut and washer?
Not all models of trailers have the nut and washer, so don’t panic if you don’t see them. Once the nut and washer are off, you should be able to just jiggle the hub off with your hands. Set everything off to the side on clean rags or newspaper.
Can you use marine grease on a trailer?
Even if your trailer doesn’t go near water, you can still use marine grease —it actually is more durable and heat-resistant than many other products. 6. Replace the bearings, hub, spindle nut, cotter pin, and dust cap. Use the wooden dowel and hammer to tap the bearings back into place in the hub.