Can I replace the stock radio in my equinox or terrain?
Yes, Virginia, you can replace the stock radio in your Equinox or Terrain (Crutchfield Research Photo) If you’re installing aftermarket audio equipment in a 4-cylinder Equinox or Terrain, you’ll need to disable the factory system’s Active Noise Cancellation functionality by disconnecting the microphones.
Is the Ford equinox loud at speed?
Like their larger cousins, the Equinox and Terrain can get a bit loud at speed. To combat wind noise and road roar, you can install Dynamat in the doors and (if you install a big sub) rear hatch area. This sound-deadening material will keep the noise out and allow you to really enjoy your music.
What size speakers do I need for my equinox or Sierra?
Both the base and Pioneer systems feature 6-3/4" front door speakers, and you can replace them with 6-1/2" or 6-3/4" aftermarket models. Again, component speakers are a nice choice for your Equinox or Sierra, so enter your vehicle information to see what’ll fit your Equinox or Terrain.
Is the Chevy Equinox a good car?
The Chevy Equinox is sleek and modern, while the GMC has the functional, utilitarian look of a good pair of cargo shorts. They're the same inside, of course, but this is way beyond the usual level of badge-enginering and it deserves some kudos.
How do I know if my car has a factory amplifier?
0:505:14How Do I Know If I Have A Factory Amplified Audio System? - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd it's usually the manufacturer of that premium system so an example could be Bose Infiniti AlpineMoreAnd it's usually the manufacturer of that premium system so an example could be Bose Infiniti Alpine Rockford Fosgate I know those sound aftermarket.
Where is my factory amp located?
FACTORY AMP LOCATIONS: The Amplifier is located under the rear seat on the passenger side. FACTORY AMP LOCATIONS: The Amplifier is located under the rear seat on the passenger side.
How do I find my car amplifier?
0:114:34How to install a car amplifier | Crutchfield DIY video - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst disconnect the negative battery terminal to protect you and your gear during installation.MoreFirst disconnect the negative battery terminal to protect you and your gear during installation. Next run the power cable from the battery to the amp. Cut a short piece of the power cable.
Do stock cars have amplifiers?
Car audio head units in all basic factory sound systems have small, built-in amplifiers to power a handful of speakers.
Where is the factory amp in a 2013 Chevy Equinox?
Registered. Re: It's under the driver's dash.
What does bypass factory amp mean?
By bypassing the factory amplifier, the music sounds more detailed and clear than it did when he used the amplifier integration harness. Whenever there's one available, we recommend bypassing the factory amp to get better sound. If you're considering a new stereo for your vehicle, keep this option in mind.
Do you need an amp for a subwoofer?
Do You Need An Amplifier for Your Subwoofer? In nearly all cases, the answer is yes. Unless you have a system in your car or boat that is already powering a subwoofer, you'll need to find an amplifier that will power your sub.
How do you hook up an aftermarket radio to an amp?
Your Step-By-Step GuideStep 1: Disconnect the Car Battery. ... Step 2: Mount the Amp. ... Step 3: Install the Power Wire. ... Step 4: Install the Fuse Holder. ... Step 5: Connect the Power Wire. ... Step 6: Install the Ground Wire. ... Step 7: Plug in RCA, Speaker, and Remote Turn-On Leads. ... Step 8: Turn It On.
How do you hook up a subwoofer without an amp?
4:396:58How to connect a subwoofer to a car stereo without an amp - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor this what you need to do is to connect the LFE jack in the receiver to the line in or in Jack.MoreFor this what you need to do is to connect the LFE jack in the receiver to the line in or in Jack. Available in the box of the subwoofer.
Do I need an amp for aftermarket door speakers?
As to the question, “Do you need an amp for door speakers or not?” it is your discretion. It may not be a real necessity, but getting an amp for these is highly recommended. It may not only be about ensuring great sound quality as you drive around.
Can you put an amp on factory speakers?
Usually, you'll be installing a 4-channel amplifier with speaker-level inputs. The best way to connect it to a factory system is to tap into the stereo's speaker outputs for the amp's input signal. Then send the amp's outputs back to the stereo's harness, and on to the speakers through the factory wiring.
How many watts are factory car speakers?
Most dealers indicate the power rating of their standard factory car stereos to be 200w.
What size speakers are on a Pioneer equinox?
Both the base and Pioneer systems feature 6-3/4" front door speakers, and you can replace them with 6-1/2" or 6-3/4" aftermarket models. Again, component speakers are a nice choice for your Equinox or Sierra, so enter your vehicle information to see what’ll fit your Equinox or Terrain.
What is the difference between a Pioneer stereo system and a base system?
Center dash speaker (Pioneer stereo system) One difference between the base and Pioneer systems is the presence of a 3-1/2" center dash speaker. Removing and replacing it is pretty simple and there are some nifty aftermarket models available.
Anonymous
The factory amp is located under the steering column. Here is a pic. Good luck!
Anonymous
I have the file on my other computer - search other bulletin boards. Check with Crutchfield help desk. Input wires are the speaker wires from the Amp head/receiver (so you can go to a BestBuy and ask them for the speaker wire colors). Black is ground. Yellow/black is main power. Blue/white is turn on wire.
Anonymous
There are only 2 things you can try to fix this yourself: turn off the engine and open the driver side door (to turn the radio off). Wait 5 minutes, start your car.
Anonymous
By using an amplifier with "HI INPUT" jack. You would use the signal from the actual car speaker wires. just tap into them and extend it to the amp input signal. I would recommend a SONY amp that's cheap and reliable. You can get one 800-100watts from ebay or walmart for about 100 dollars. Get a amp wiring kit and you are good to go.