There are a number of ways to stiffen the forestock. Option one is to order the Stock Stabilizer from Nathan Forester (www.ballisticstudies.com). On my Savage 111 in 7mm Rem Mag i cut a carbon arrow lengthwise, cut 2 channels into the stock and epoxyed them in.
Full Answer
How do you stiffen the fore end of a stock?
If you decide to stiffen the fore end with resin, apply in thin layers as the heat generated by the curing can warp the stocks fore end if done in too thick a layer. Rifle stock and pistol grip reproduction. I earned every grey hair I have.
Is there any way to make a timber stock stiffer?
I doubt it, the timber stocks are the 2nd best for stiffness,all the wood fibres run in the direction that is good for compression. Whatever you do to a synthetic stock with epoxy will also stiffen a timber stock, you could even add some S Glass with the epoxy to make the timber stock even stiffer.
What do you use to stabilize your rifle's stock?
I took the rifle apart, ground out the cross sectional 'stabilisers" (what ever the technical term is) and epoxied some carbon fiber in the stock forearm. Carbon fiber is cheap in a ribbon my the meter off ebay and a small tin of epoxy from the local hardware.
What to do about a sticky fore stock?
I had a very sticky fore stock on my Duratouch Camo Winchester SX2 shotgun. Sprayed it with Rust-Oleum matte clear clear coat spray. Looks and feels great and smooth. Matches buttstock perfectly.
Can you bed a synthetic stock?
0:042:56Quick Tip: Introduction to Bedding Stock - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut what do you do with wood stocks and composite stocks are basically any stock that doesn't haveMoreBut what do you do with wood stocks and composite stocks are basically any stock that doesn't have bedding in it already. Well the solution is to use an epoxy type bedding such as the ekor glass.
Can you free float a synthetic stock?
0:282:36FLOATING A RIFLE BARREL - SYNTHETIC STOCK - YouTubeYouTubeStart of suggested clipEnd of suggested clipEven the manufacturer puts these ribs in here and I do not know why when they could eliminate themMoreEven the manufacturer puts these ribs in here and I do not know why when they could eliminate them in the molding process and all barrels would be free-floating.
What is the buttstock of a gun?
A gunstock or often simply stock, the back portion of which is also known as a shoulder stock, a buttstock or simply a butt, is a part of a long gun that provides structural support, to which the barrel, action, and firing mechanism are attached.
What are polymer gun stocks made of?
Synthetic materials for handgun stocks include a variety of molded plastics of various colors, as well as laminates such as Micarta, a high-pressure laminate of layers of linen cloth and resinous binders. Also popular are various soft-rubber units of one- or two-piece construction.
Is a free floating barrel more accurate?
When we say that free-floating a barrel improves accuracy, what we really mean is that it improves precision, the ability of the rifle to shoot the bullets to the same spot each time.
What does a free floating barrel do?
This minimizes the variance in possible mechanical pressure distortions of the barrel alignment, and allows vibration to occur at the natural frequency consistently and uniformly, shot-by-shot.
What is a Mannlicher stock?
Mannlicher stock (plural Mannlicher stocks) (firearms) A stock on a rifle that runs the full length of the weapon.
Does putting a stock on a pistol make it an SBR?
While it is legal to add a Stock or a Folding Stock to a pistol, doing so will create a SBR which must be engraved and approved using an ATF Form 1 prior to doing so. In fact, having a stock and a pistol in close proximity with the present ability to configure it as an SBR could be constructive possession of an SBR.
What does drop at heel mean?
Drop at Heel: extent of vertical offset between the top of the barrels (rib) and the heel of the butt-stock. Cast: extent of offset left (cast on) or right (cast off) between the midline of the barrels and the center of the butt.
Are laminated gun stocks good?
Bottom line: A laminate is just flat-out better at being a gunstock than the traditional one-piece chunk of wood. Not only is it much stronger and stable, it has a tactile warmth about it that no synthetic can match.
What is the best material for a rifle stock?
A Comparison of Gunstock MaterialsWood is the traditional material and of course nothing looks better to most people than a fine piece of quality gun stock wood. ... Synthetic stocks are generally stocks that are injection molded and are available at low cost.More items...
Are synthetic stocks lighter than wood?
There's a common notion that synthetic stocks are lighter than wood, but this isn't always true. Depending on whether they're solid or hollow, along with how they're designed, synthetic stocks can weigh as much, or more in some cases, than wooden stocks.
Why did the shooter in question think he was developing a flinch?
And to top this off, the shooter in question didn't realize, even with his vast experience, that he was canting his rifle, and thought he was developing a flinch because he was getting too old for the large caliber. Took another shooter observing him to spot the problem.
Is synthetic stock flex bad?
So, some synthetic stock flex so much that when you are resting the fore-end on something they make contact with the barrel. This, as you know, is bad.
Can you stiffen the fore end of a stock?
If you decide to stiffen the fore end with resin, apply in thin layers as the heat generated by the curing can warp the stocks fore end if done in too thick a layer.
Can you use epoxy to stiffen timber?
Whatever you do to a synthetic stock with epoxy will also stiffen a timber stock, you could even add some S Glass with the epoxy to make the timber stock even stiffer. I prefer Alloy stocks, no bedding required which cuts some costs if going that route and it's the stiffest option. Baronvonrort.
Carbon Arrows to stiffen forend on synthetic stock
I have been looking for a SA cf stock with DBM for a while now and couldn't make my mind up. I stumbled on a Hogue overmold on Midway for $99. Took a chance, and it is actually a pretty decent stock. It has aluminum pillars, and the action and bottom metal all just dropped right in for a perfect fit.
Re: Carbon Arrows to stiffen forend on synthetic stock
Do you have any pics of how to do it so it dosen't interfere w/ the barrel?
Re: Carbon Arrows to stiffen forend on synthetic stock
did you dremmel out the "ribs" in the stock, put the arrows shafts in, then expoxy the whole thing? It would seem to me that that would make it stifffer
Re: Carbon Arrows to stiffen forend on synthetic stock
did you dremmel out the "ribs" in the stock, put the arrows shafts in, then expoxy the whole thing? It would seem to me that that would make it stifffer
Re: Carbon Arrows to stiffen forend on synthetic stock
What are the pros and cons of carbon arrows versus aluminum ones? Just wondering.
Re: Carbon Arrows to stiffen forend on synthetic stock
I used an aluminum arrow and it worked okay. I found this the other day while I was searching for flush cups and it looks like it might be a good idea although I have not tried it. http://www.ar15.com/forums/t_6_5/230395_.html&page=2
Re: Carbon Arrows to stiffen forend on synthetic stock
Good stuff. Been hearing all kinds of talk about the flex of the savage stock and wondered what options there where if problems did persist. Right now my barrel is free floating all the way to the recoil lug, but with the addition of a bipod it is going to push it closer for sure.