The sections are 34" 21" and 10" To connect the AN hose to the stock system you need a couple AN to hose barb adapters. The stock hoses are damn close to 3/8" and the 8AN fittings are slightly larger than that.
Full Answer
Where is the transmission fluid cooler on a 700R4?
the 4 speed auto has a few different names but i came across this information. "Transmission fluid cooler lines: on the 700R4 the bottom fitting on the right side of the transmission is the "out" line to the cooler and the top fitting is for the return line from the cooler.
Where does the transmission fluid drain out of a 4L60E?
Once the hot fluid flows into an through the factory cooler, it then exits at the top or other side to the cooler outlet or return line, which is the top line on your 4l60e. This would be the line you’d tap into if you were looking to install an aftermarket external transmission cooler.
Where is the coolant inlet line for the radiator?
FYI, some vehicles have the factory cooler on the bottom of the radiator, but simply follow the lower cooler line coming from the transmission to find the hot or cooler inlet line.
Do the Trans and radiator lines have to be valved?
The factory part is one solid line from trans to radiator. The fittings at the trans are the same part number for both the supply and return. Since the fittings both go the same direction into the trans, you'd never get flow if they were valved.
What size are transmission cooler line fittings?
Transmission Radiator end of fitting has 1/4" MPT. line fitting is 1/2"-20 inverted flare INS. - Factory fitting remains with recessed internal threads.
Are oil cooler lines and transmission lines the same?
The oil cooler is based on the same flow-through principle as the transmission cooler. It is installed in-line with the vehicle's oil delivery system, and then the oil pump pushes oil through the cooler and back into the engine.
What PSI is transmission cooler lines?
The cooler pressure is not published anywhere that I can find but most automatic transmission's have about 4 to 10 PSI. You have to keep in mind the cooler pressure is low because the oil is flowing to lubricate the gears and there is not much resistance in the lines.
How much pressure does a transmission line hold?
During normal operation, its about 150 and the return line around 50 psi.
What can I use for transmission cooler lines?
Due to the chemical properties of PTFE hose it's a perfect fit for using braided lines for your transmission fluid lines.
Which transmission cooler line is the return?
The cooler of the two lines is the return line and the one to install the transmission cooler on.
Do you need to bleed transmission cooler lines?
Do i need to bleed the cooler once installed or will the air just get flushed out? Expert Reply: You would not need to bleed the transmission cooler part # D13503 before you install it on your truck. The fluid is thick enough and the pressure it high enough that air bubbles would immediately work themselves out.
Is transmission fluid under pressure?
ATF is pressurized by the transmission oil pump that is driven by the engine. The pressurized fluid flows through the transmission to engage and disengage the clutches and bands. A valve body, usually located in the bottom of the transmission, controls the fluid flow to the clutches and bands.
How do you stop a transmission line from leaking?
3:317:59How I Fixed a Leaking Cooler Line for Free - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd what I'm gonna do is I'm going to use multiple clamps per end and put plenty of rubber hose overMoreAnd what I'm gonna do is I'm going to use multiple clamps per end and put plenty of rubber hose over the steel lines to reduce the chance of them coming off or leaking.
How do you fix a transmission line?
0:083:20How To Repair Damaged Transmission Lines (Andy's GarageYouTubeStart of suggested clipEnd of suggested clipLine with the flared ends. And then using compression fittings on both ends to connect it to the toMoreLine with the flared ends. And then using compression fittings on both ends to connect it to the to the parts of the transmission. Line after you've cut out the bad section.
How do transmission cooler lines work?
These lines pull transmission fluid from the transmission and take it to the radiator, where it cools down. They then circulate it back to the transmission where it keeps doing its job. Like all parts of an engine, transmission cooling lines can wear out.
What should the line pressure be on an Allison 1000?
about 230psiOne of the cheapest and simplest durability additions anyone can make to their 2011-2017 Allison LCT 1000. From the factory line pressure on the LML/L5P trans reaches about 230psi, but only during shifts.